Alan Gordon 5
-
Posts
51 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Gallery
Calendar
Downloads
Everything posted by Alan Gordon 5
-
The present tank is 56.5 ml square, with an over all lenght of 120 ml I think I will try as Nigel suggestes getting a smaller tank but longer, will scout around the web !!
-
Interesting regarding the polish, guys, I realise that enclosing the tank in foam would help but this being an ARTF the tank is good fit and I would have to cut away the former holding the tank to fit foam then I would be concerend with regards to loosing structural strenght. I take on board also the need to balance thr prop / spinner.
-
I thought about cutting away the formers as this seemed the way to go with sponge surrounding the tank but being ARTF was concerned with weaking the structure. Will check prop balance though !
-
Hi Guys, I have aquired a Seagull Extra 300 with a Super Tigre 91 up front, No problems apart from the tank as supplied is a tight fit in the formers, the trouble is vibration in tank which in turn is causing bubbles in the fuel delivery to engine which in turn is causing eratic running, Any ideas on how to insulate tank to minimise this adgitation ?
-
Thanks for the help and advice folks, will take all on board.
-
Hi Guys, Looking on advice for a new power panel, Any recomendations ? I
-
Wheel size
Alan Gordon 5 replied to Alan Gordon 5's topic in Vintage Kits, Semi-Kits and Plan Projects
The plan I have was damaged, sods law if there was any info it aint there now ! Thanks for your help I will get a set ordered. -
Hi Folks. I am in the final stages of building a Ben Buckle Red Zephry ,any advice on wheel size would be appreciated.
-
Hi Don, Sincere apologies, I did respond but obviously it did not get through, To answer your question I purchased the kit and all the extras I think around the end of 2017. But I simply do not have the time to start.
-
Hi Guys, I am going to have reduce the price of my SE5a which at present is in the classifieds, but how do I edit the current posting (or can it be edited ?)
-
Hi Guys, I am about to start a DB sport and Scale Quarter scale SE5a, can anyone advise me where I buy quarter scale eyelets ?
-
Mine was a Skyway Hawk 70 ( now a Masons Models) This was was semi scale but simple to build and a joy to fly
-
Morning chaps, I have a 91 fourstroke kicking about and desperate for an airframe. I would like to put it in a vintage type model any ideas on a model large enough.
-
Thanks Lads for all the info, Job done
-
Hi Frank Thanks for that but does the small slot in the hinge run parrale with the trailing cos the hinge can go in one of two ways Regards Alan
-
Hi Guys, I have just started to assemble an Acro Wot. The hinges are a loose fit until glued in, however I notice that each hinge has a small pre cut slot. My question is this, are the hinges glued in with this small slot parrarel with the trailing edges or at ninety degrees to the trailing edge ? Hope this makes sense Edited By Alan Gordon 5 on 27/01/2018 07:46:59 Edited By Alan Gordon 5 on 27/01/2018 07:48:04
-
Thanks for the info guys, much appreciated and taken on board
-
Hi Guys I have a spare 10cc 4st. I would like to put it into a low wing sport / aerobatic model, I dont have the time to build so looking for an ARTF model, any suggestions on what I should get would be appreciated. Alan
-
Excellent advice chaps, many thanks
-
Thank you gentlemen, Plasterboard it is Regards
-
Hi Folks Need to build a new building board. The construction of the board is not a problem but I was going to lay a sheet of Sundela on top. Would this be suitable ? or is there an alternative some one could suggest.