Pat (rActive) Harbord
-
Posts
687 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Gallery
Calendar
Downloads
Posts posted by Pat (rActive) Harbord
-
-
Not quite right - the tail fin is different on both
Senior Executive is close though
Pretty sure it would have been powered by an os OS40
This is going to be one of those ‘i’ll know it when I see it’ jobs
keep ‘em coming
-
That would make sense, room to expand. He always had his eye on the future.
Must have cost a fortune
-
Photo of my late father.
I remember at least 3 Super Flies (Waterhouse and Eley) from this era (the last one with a yellow fuz rather than the usual orange)
This is something else though - I don’t remember it, so could be pre 1975.
The transmitter will be Skyleader or Futaba
He later progressed to a lovely Fournier RF4 after seeing Mick Reeves’ scale job at the 1978 Nats
and then a full aerobatic job like a Curare (but an American design as I recall)
All those trainings did the job
Sorry for the bad cropping (not my photo)
Any ideas?
-
1
-
-
Agreed: **LINK**
-
My FC board is identical to yours Martyn - Yes that is where you will need to solder a header for the i2c board
-
It's alive! - Just made first tentative hovers (indoors with horizon mode on) - I'm going to enjoy this, love the sound.
Props arrived from HK yesterday, which meant I have had loads of time to setup and configure the board. Really need to wait for the wind the calm down before getting outside and really working on the PID settings.
Rx is an Orange R615X connected PPM with only one lead for all channels and aux. This makes for a very tidy installation
Can't make too many assumptions about stability as I'm either in ground or ceiling effect in the lounge - but directional stability is pretty good - just a bit of drift to the back and right, easily controlled with a dab of opposite stick.
I'm running a F450 clone frame - with the Multiwii 328p FC - generic red 20Amp SimonK esc's - 920Kv 2212 motors - 9443 props - I've got GPS components ready to go on once I've found a PC to borrow as I can't find a config app to run on the mac.
££'s to date - around £120
Thank you BEB for driving this thread and for all contributions that have allowed me to stalk around in the background gleaning the necessary info to get up and running.
Ultimate aim is to get a camera hanging under it as I have a potential commission to shoot a friends engineering facility - I can already see this could be a slippery slope, Shahid Banglawala's heavy lift series looks alarmingly relevant all of a sudden.
-
Bind the brick buy turning on the (plugging in) the receiver first, the onboard led should start flashing (bind mode). Then turn on your transmitter in bind mode (hold trainer button on my DX8 - having previously selected a new model memory. Binding should ensue. I'm building the Neuport from the same range, I can't say currently building as it's been on the board for over a year.
A donf
-
I saw an aircraft I had completely forgotten about but instantly recognised at around 4pm on Sunday over Buckingham heading South - an Edgley Optica, to far away to see the index. Don't think I've seen one since the early 80's
-
Posted by Biggles' Elder Brother - Moderator on 22/05/2015 23:42:59:
Absolutely no reason what so ever Pat. Controller boards are not in any real way linked to airframe size.
BEB
Superb, I'll get components ordered then. This is going to be fun.
-
Any reason I couldn't use the same controller components in a bigger frame? This thread has provided the nudge I've been waiting for to build a quad. Just thinking a 450 frame would allow me to expand into fpv.
-
As I recall it was part of an installation in Tate Britain. There was a long mechanical production line that was supposed to take the raw components and assemble, then launch a plane every 2 minutes. I don't think it ever worked. There was one single example on a plinth under glass that turned out to have been made by hand. Tate never admitted it, but the common view is the artist was being ironic and it was never meant to work.
-
I was going to ask you for a cheeky discount
-
Mick, are you associated with unmannedtechshop?
-
Hmm, I'm going backwards (like mclaren) I forgot to do predictions in the first round and did better than I did today. Cracking race though
-
Looking superb Jez. Good to hear you're all better. Like Danny, I was getting withdrawal symptoms.
-
loving all the scale detail - Very impressive, I imagine it is helium filled. Might only weigh a few grammes.
-
non shrinking dope is also known as 'banana oil' due to the smell I belive
thin 50/50 and add talc bit by bit, works great.also second what Dave said, probably much cheaper than dope these days
-
Session up and running now
Modelflying/rcme
-
A tilted stab is a traditional (and effective) way to trim free flight models.
Your pc9 will want to roll and yaw so the stab is level. You may find a couple of clicks of opposite aileron and rudder will have you flying straight and level, but there will be some extra drag. Better to fix at source if you're feeling up to the surgery required.
-
Smashed it this morning - I maxed out on brownie points with a bar of fruit and nut and a cup of tea in bed
I also sourced the cause and unblocked the drains and septic tank (who said romance is dead?)
problem is, she won't come anywhere near me now
-
‘Fair dealing’ is a legal term used to establish whether a use of copyright material is lawful or whether it infringes copyright. There is no statutory definition of fair dealing - it will always be a matter of fact, degree and impression in each case. The question to be asked is: how would a fair-minded and honest person have dealt with the work?
so no grey areas as such, but you only get clarity when you test the law against specific scenarios.
-
I agree Erfolf, it all comes down to money in the end
"Your ideas are worthless, unless they are in our employment, then they may have some worth. Which sums up, without money or the backing of a company prepared to fight, it is difficult to enforce your rights."
very true
-
You can have 1 copy of just about anything for personal use - I imagine Staples turned you away because you asked for multiple copies? They are just being silly.
Copyleft - absolutely necessary for real open source collaboration, great idea
-
I'll play again - I promise to pay more attention to the league this season
not coming last again, that's for sure - famous last words
bring it on
70’s trainer identification
in General Vintage R/C Chatter
Posted
I think there’s no radius at the top of the tail fin - This could mean he didn’t sand it in of course
I think it may have been 3 channel looking at the amount of dihedral?
I wonder if it was a SuperFly ‘antidote’ as I know he got through a few and they where a little on the heavy side