Chris Ireland Posted October 5, 2008 Share Posted October 5, 2008 Hi Guys, given the appalling weather whenever I was available to go to the field in my attempts to learn how to fly this year I have made very little progress so I thought that I might try to do some indoor stuff over the winter… So having asked around, done some research etc I finally made a purchase of a ‘foamy’ and all of the attendant gubbins I needed to get it into the air.Building the thing is no problem; snip, cut, glue, pin, trim, swear etc in all of the right proportions as dictated by the instructions, or lack of them. My problem arises in wiring the electrics. Obviously, the servo to receiver connections are straight forward, as are motor to ESC and ESC to receiver (‘Thro’ socket). My problem, and hence my question, lies with the battery. The battery is a very slim 400mAh 3S 20C 11.1v LiPo with only two bare wires and no balance lead. My ESC, as previously mentioned, has easily identifiable motor and receiver connectors plus two bare wires (sounds like a battery feed to me). Since this is an electric airplane I am presuming that I need to power both the receiver and the motor. Is it just a matter of using a ‘Y’ connector to couple up to both the bare ESC wires and the ‘Batt’ socket on my receiver or am I missing something vital? Thanks in anticipation….. Quote Link to comment Share on other sites More sharing options...
Bruce Richards Posted October 6, 2008 Share Posted October 6, 2008 The two battery leads connect to the two leads on the ESC make sure you get them round the right wayred to red black to black. The ESC should have a BEC (Receiver Battery Eliminator Circuit) to power the Rx and servos. The power comes down the red and black wires from the ESC to the Rx throttle channel. Quote Link to comment Share on other sites More sharing options...
Tim Mackey Posted October 6, 2008 Share Posted October 6, 2008 I am unsure as to which cabling you are referring to. The 2 x main power leads from the ESC should be readily identifiable and either coloured red /black ( or maybe blue ) and obviously conect ( via suitable plug/socket ) to the flight battery. If these are not coloured, then there will likely be a marking on the ESC itself ( it may be a bit hidden ) showing +/-The ESC will also likely ( as Bruce says ) have a BEC lead coming off it. This looks like a servo lead, and plugs into the throttle channel, supplying power to the radio and allowing throttle position commands to be fed from the Rx to the ESC.I dont like the sound of "2 x bare wires" coming from the LiPo !Please post a picture - do NOT connect anything up until we are sure we know what is happening here. Quote Link to comment Share on other sites More sharing options...
Former Member Posted October 6, 2008 Share Posted October 6, 2008 [This posting has been removed] Quote Link to comment Share on other sites More sharing options...
Chris Ireland Posted October 6, 2008 Author Share Posted October 6, 2008 Thanks chaps, I've fallen into the trap again of assuming you can make sense of my inadequate descriptions... DOH!Indeed the 'bare' wires are colour coded black and red. I guess I was trying to imply 'bare' = 'wires without fitted connectors' rather than 'wires stripped of insulation'. The ones on the battery are also insulated with heatshrink so there is no immediate danger of shorting. I will only be uncovering them one at a time for connection purposes and recovering/insulating each before I move on to the next step.I had lost sight of the BEC aspect of ESCs so your reminders are both welcome and make me feel a bit dumb. I had looked through several pages of posts on the subject but nothing had triggered my personal "Doh, that's it" circuitry. Additionally, there was nothing mentioning BEC connectors on the comprehensive instruction sheet which came with the ESC. I guess the manufacturers assume a basic level of knowledge which I appear to have slipped under... Old age, don't ya know... well that's my excuse for the moment...Fortunately, I am of the "measure twice, cut once" school of engineering so there was no chance of me connecting a LiPo without seeking advice or knowing what I was doing.Here's the equipment in questionI am proposing to use a couple of 'mini' deans type connectors with the negative from the battery connected to the protruding pin as layed out in the picture. Do you think that I would be better off using full sized Deans connectors, of which I have a supply, with the protruding pins coming from the ESC, as per standard battery practice, given that we are talking LiPo's here? I think that I have probably just answered my own question as the weight saving aspect is more than outweighed by the safety considerations.Bruce, Timbo and Eric.... as always, thanks for the informative replies and being there to assist us all when we cry for help. The greatest danger is when we don't know that we need help and don't cry out! Quote Link to comment Share on other sites More sharing options...
Bruce Richards Posted October 6, 2008 Share Posted October 6, 2008 Be very careful when soldering the battery connector as you say do them one at a time and cover with heat shrink befor doing the next. Then keep the Iron away from the heat shrink to avoid melting it. I agree that the larger Deans would be better or better still (in my opinion) bullet connectors. Quote Link to comment Share on other sites More sharing options...
Chris Ireland Posted October 6, 2008 Author Share Posted October 6, 2008 I think that I will go with the full size Deans solution as that will fit in quite nicely with my current charger connection rationale and avoid having to make up yet another converter lead. Thanks. Quote Link to comment Share on other sites More sharing options...
Bruce Richards Posted October 6, 2008 Share Posted October 6, 2008 That a good reason to go with the Deans. Quote Link to comment Share on other sites More sharing options...
Tim Mackey Posted October 6, 2008 Share Posted October 6, 2008 Yup. Quote Link to comment Share on other sites More sharing options...
NealeG Posted November 5, 2008 Share Posted November 5, 2008 Just in the process of setting up my first electric model and I have one additional question relating to the installation. On IC's we use a receiver switch! does this not apply when using electric setups? Quote Link to comment Share on other sites More sharing options...
Bruce Richards Posted November 5, 2008 Share Posted November 5, 2008 That is correct. By connecting the battery you both make the power setup live and turn on the radio set. Once the battery is connected the model should be treated with all the respect you would give a model with a running IC engine. Quote Link to comment Share on other sites More sharing options...
Chris Ireland Posted November 5, 2008 Author Share Posted November 5, 2008 When I used to run an electric racing cars we all fitted on/off switches. Is there a reason why electric planes/helicopters do not have one fitted? It would seem to make sense from a safety point of view, given that the machine is 'hot' while you are fiddling around with wings/covers/canopies etc in fairly close proximity to a prop or rotor which can easily be set in motion by a very small inadvertant movement of the stick (or someone else's transmitter if frequency control is ignored/compromised). Am I missing something (again) here ? Quote Link to comment Share on other sites More sharing options...
Ralph Yeates Posted November 5, 2008 Share Posted November 5, 2008 Timbo maybe you could do a sticky in the electric or newbie section on the BEC questions as it seems to pop up a lot ref how it all connects together. Quote Link to comment Share on other sites More sharing options...
Chris Ireland Posted November 5, 2008 Author Share Posted November 5, 2008 Hi Ralph, thanks for labelling the picture, hopefully it will be useful to others if Tim can make a sticky incorporating it. I really should have used a better background rather than my grungy bench with a soiled mat on it....I'm assuming that an on/off switch, if fitted, should live between the ESC and the Receiver to inhibit the passage of signals to any of the equipment. Of course this would still leave the possibility of a signal being passed in the event of an ESC malfunction. Am I right in assuming that if it was fitted between the Battery and the ESC there is the likelihood of getting too much current through it when the motor is working hard ? Quote Link to comment Share on other sites More sharing options...
Ralph Yeates Posted November 5, 2008 Share Posted November 5, 2008 The Castle creations don't have a switch but the Ripmax one does it is on a fly lead from the ESC. The Castle one powers the receiver then when you close the throttle it primes the motor with audible beeps to warn you its armed & dangerous but to fully disconnect you need to unplug one of the battery leads bit of a pain when they could incorporate a small switch in the ESC would only cost a few pennies at manufacturing. Quote Link to comment Share on other sites More sharing options...
Tim Mackey Posted November 5, 2008 Share Posted November 5, 2008 I prefer the ESCs which do NOT have an isolating switch fitted! IMO the ONLY sure way of isolating the power to the motor is by physically unplugging one or both of the main battery leads. A switch or other isolator in the main leads is only practical in heavy large models, as this device needs to be able to handle a very high current, and therefore by its very nature will be large and bulky - I know some people have successfully incorporated a DEANS plug /socket mounted in the fuselage and used as a bridge. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.