[2018 PSSA Mass Build - The Completed Model Thread]

Just exhaust to add colour scheme 1940 experimental camflouge finished in oratex and spray painted finished AUW is 4Lb. 1 Oz abit on the heavy side but should be ok had to add 1Lb 1Oz of lesd.

[Hurricane Building Tips and Plan/Woodpack queries]

thanks for the reply Phil the only addition to the plan i used 2 servos for the aelirons i think perhaps i did not shave enough wood off the rear end.

[Hurricane Building Tips and Plan/Woodpack queries]

I have just completed mine and did a trial balance and found that had to add 1lb 1oz to get it to balance giving me a flying weight of 4lb 1oz , i have covered it in oratex and spray painted i would not have think that would have increased over a 1lb on the protoype weight any thoughts ???

[Hurricane Building Tips and Plan/Woodpack queries]

I would like to thank the developers of the hurricane and that this is the place for building tips and small corrections required and not the place for criticizing all the work that has gone into this project.

[An Introduction to the PSSA 2018 Mass Build Project]

Hi Phil have now corrected and i always do trial dry fit so no problem

[An Introduction to the PSSA 2018 Mass Build Project]

Cheers Andy

[An Introduction to the PSSA 2018 Mass Build Project]

Just put fuz sides & front on bench the front key does not fit in cutouts on side there is about 1/8" gap each side am I missing something ??

[An Introduction to the PSSA 2018 Mass Build Project]

Received my kit yesterday making a start soon. Here is a link to a lot of possible colour schemes https://www.google.co.uk/search?q=&tbm=isch&tbs=rimg:CZzRlPpQ7RtNIjjWXUQ9eVCTfLl9v7cjZVCv61uMZ72AFEVCti4DLYx_11zn6lUBUXCGjFTt-ijAzqCEar8YS_1z_1XuSoSCdZdRD15UJN8EXitDj8qfNd4KhIJuX2_1tyNlUK8RmyMUl0Recq0qEgnrW4xnvYAURRFOPdIltV6K9ioSCUK2LgMtjH_1XEcTEDTCgknEhKhIJOfqVQFRcIaMRRFmodmOXknAqEgkVO36KMDOoIRHkamoUrss-9yoSCRqvxhL_1P9e5Ee5n5ZTKHCXk&tbo=u&sa=X&ved=0ahUKEwiHy8W-tt_ZAhWKIsAKHQC7Bo4Q9C8IGQ&biw=1920&bih=922&dpr=1

[PSS A-4 Skyhawk - The completed model thread]

Maiden flight today for myself & Bryan Tucker at Frocester hill near Stroud, wind strength was 18 to 25 MPH. flights went well with 2 landings with no damage.

[PSS A-4 Skyhawk - The completed model thread]

ET Equipments that was a while ago. see you in september Andy

[PSS A-4 Skyhawk - The completed model thread]

I had intended to do a paint job but then came across a dark blue roll of pro film i had forgotten i had no it is not matt.

[PSS A-4 Skyhawk - The completed model thread]

This is my first post just finished my A4 the build went quite well I decided to glue the air intakes to the fuz before covering then it would be easier to blend the edges with light weigh filler.
The final all up weight was 2lb 5oz, the balance was achieved by just the battery pack fitted fully forward.

[Sebart Sukhoi 30]

Hi David

Thanks for the advice

[Sebart Sukhoi 30]

Just finished the Sukhoi any advice on first flight, i am a fairly compentent flyer but mainly gliders but have some small electric models the largest being a Dingo from Puffin Models.

thanks Brian