Jump to content

Ian Jones

Members
  • Posts

    4,637
  • Joined

  • Last visited

Posts posted by Ian Jones

  1. Posted by Tim Hooper on 27/08/2018 21:15:28:

    We had our first visit there last year, and we're going again next month. 'nuff said!

    Tim

    Speaking to those here it seems there are a lot of regulars. Actually Tim, your review helped with my decision to go there . Thanks.

  2. Hi Andrew,

    Pretty much what it says, you can bring your own model (s), or if you want as in my case and most others I think, fly the models provided by the hotel. I'll get some more photos done and post them.

    The hotel is near Poulades, an inland site with extremely helpful and friendly staff. It is family run and the owner, Spiros, will do what he can to try and arrange anything you may need of its at possible.

    Edited By Ian Jones on 25/08/2018 11:57:11

  3. img_20180824_122640.jpgAh, right, so your mobile phone will not give you the full editor for posting (images etc.), Then switch to the desktop site and your in.

    Here at the RC Hotel is been blazing hot every day until today with a threat of rain is been cooler but more muggy, didn't stop me flying thoughsmiley.

    Anyway, here's a few photos.

    img_20180823_114556.jpg

  4. Well Martian, if you can walk away from your printer to the living room you are really making progress! wink 2

    I'm just setting up a security camera for my printer, not in case the SWMBO decides to do a way with it, no, no, it's so that I too can sit in the living room and check now and then that that lengthy print is progressing okay.

  5. Posted by Tom Sharp 2 on 15/07/2018 22:47:58:

    I bought a flying wing thing once, instructions said cover it in bullet tape. It's still in the corner waiting.

    What is bullet tape.

    It's that cross weave fibre glass reinforced stuff Tom. Often also referred to as CW tape (Cross Weave) as well as bullet tape..

  6. Hi r6dan,

    First time I used the stuff was indeed on an Si Zaggi, to my surprise with good success. So without claiming to be any expert I'll tell you how I use the stuff (same method with the coloured tape too).

    First of all clean the scissors thouroughly with meths and repeat this after every cut; a pain but clean scissors will make a huge difference.

    Ensure there is no dust, hairs or any other such like debris on the model. Unroll suffient tape to overlap the length really needed, then lay it very lightly, zero pressure in place on the model. Carefully cut it free from the roll.

    Now the tricky bit! starting from approximatley half way along the strip, smooth it down a few inches at a time, working outwards from any imaginary centre line. If the tape has been laid down without any pressure it will lift in front of the smoothing action like a barely visible mini wave. Take time and work along the tape towards one end then return to the middle and do the same towards the other end. Now the tape is place I then go over it again with a little more pressure to ensure it is properly adhered to the surface. I have found fingers the best equipment to use for the smoothing.

    If for any reason I have to lift the tape after I've started to smooth it down then I throw the strip away - the process of removing the tape will have distorted it and it just will not go down nicely a 2nd time.

    Well, that works for me, best of luck with your next one.

    Edit: Oh, the the model concerned is in my avatar.

     

    Edited By Ian Jones on 15/07/2018 19:27:04

  7. Not perfect I agree but it does give the nearest indication we can get of what might happen on climb out after leaving the ground. The object being to try and avoid an Engine Failure After Take Off.

  8. 3rd model I ever bought, more than a few years ago now, a Ripmax Se5a. Flown it every year since just at the club or further af field, including a visit to (the 1st?) Delyn Scale Flying Competition, Greenacres and a BMFA scale day at RAF Shawbury.

    I hold my breath every time I say the next bit for fear of tempting fate, it's had no crashes, no structural repairs just a new undercarraiage, still sports it's orpginal covering (though not for much longer TBH), the SC52FS purrs as happy as can be, it looks great and finally it's reasonabley aerobatic for what it is.

    Club flying:

    se5 1(2).jpg

    Delyn Scale Flying Competition:

    Delyn 2010

    All these years it just keeps on going, what more could I want.

    A close second would be my Sportster:

    canon slr july selection 2012 022.jpg

    What would I wish for? A twin turbine Sea Vixen, what else is there to wish for?wink 2

  9. Not JR but on a similar vane, I use several Hitec Modules (in Futaba & Hitec module type transmitters) and one "built in" Hitec Transmitter. With these I use genuine Hitec receivers, FrSky comaptible receivers, and Ikonnik KA-6 compatible receivers; all without issues.

    The issues with the JR modules/transmitters seems very strange, has anyone else experienced the same problem I wonder. Are oreange receivers cheap enough to try out a new one as a test?

  10. Posted by Megawatt on 08/06/2018 11:45:31:

    I think I need to challenge the assumption that this legislation is to clear the airspace above 400' for commercial drone ops. Full size aircraft are subject to a 500' rule and it is quite legitimate for them to descend to that height for whatever reason and remain legal. IMO the 400' limit and 1KM from an airfield is to allow separation from full-size aircraft and ensure that any increase in commercial drone ops remains segregated from manned aircraft. We shall be sharing the 0-400' range with them.

    Sounds right to me.

    That said, 400' is painfully low. Fly at 200' and pull in a large loop or go up for a good old multi rotation spin (bearing in mind the need to pull out well before the crunch) and it's easy to get up there. As for thermal gliding, 400' is nothing. I've tested all this with GPS telemetry and found it to be so.

    I beleive a lot of the fun we freely enjoy at the moment could be affected in such a way that it just won't be worth doing.

    I don't suppose they'll be any compensation scheme for those forced to abandon £K's worth of models & equipement.

    I hope BEB's optimism turns out to be correct.

  11. Posted by Geoff Sleath on 08/06/2018 12:28:08:
    Posted by Ian Jones on 08/06/2018 12:06:40:tripping over the buddy lead when walking to pilots box.

    Another point in relation to beginners is, who does the early take-offs anyway? The instructor does. If he does so from the pilots box then the novice is already becoming accustomed to that view.

    I seem to remember when I was learning (I still am!) I wasn't allowed to take off until I could land, which seems sensible as take offs are much easier - it's getting the model back down safely (and hopefully elegantly) that's hard.

    Geoff

    That's a good point too Geoff, learning how to make an aborted landing can't be done from behind the model and a take off has a lot of similarities to a low level abort, apart from the ground run of course.

    I too wondered if, as Martin suggests, there's an element of "this is the way we've always done it"? Though perhaps Andy's comment answers the OP.

    It would be interesting to hear from a NATS regular on this point.

  12. As well as the safety issues already mentioned, which I totally agree with, standing behind the model gives the pilot an unusual view of his model!

    At all times during the flight the pilot is (or should be), in the pilot's box and therefore is viewing his model from the same position. From that position he is controlling the speed and direction of the model and also from that position he has to conduct a landing, which unles it's a crash results in the model travelling along the strip in a controlled manner - similar to a take off. So it makes no sense at all to stand in a different place for take off.

    It doesn't make any sense to me to teach a beginner to take off from behind the model then change his position to one he is not accustomed to later. I have found training beginners to take off from the pilots box no more difficult than training them to take off from behind the model, furthermore if a buddy lead is in use there's no tripping over the buddy lead when walking to pilots box. Progressing to learning to take off involves(for me at least) teaching ground handling first, from the pilots box, so again why take off from anywhere else.

    Another point in relation to beginners is, who does the early take-offs anyway? The instructor does. If he does so from the pilots box then the novice is already becoming accustomed to that view.

     

    Edited By Ian Jones on 08/06/2018 12:10:55

  13. Hi David,

    Disappointed to hear this news, you were making an excellent job as editor, however looking after your health, as I know very well, must come first.

    Good luck with your future plans, don't pack up but keep them within your own personal limits.

    All the best, Ian

     

    Edited By Ian Jones on 29/05/2018 12:53:00

  14. Would be good but is this a demonstration of an idea rather than a working model?

    For example what happens when RF signals are introduced into the equation - for our purposes essential.

    Those servos don't just simply work, there's a control system which needed switching on for each one.

    Still I hope it does come to something.

×
×
  • Create New...