3D Printing

127 topics in this forum

1. Some experiments with "Lofting" in FreeCad

   By Simon Chaddock, November 17, 2022
   • 5 replies
   • 830 views
   • 
   • Simon Chaddock
   • June 18
2. Advert
   
   
   

3. PrusaSlicer -- how to stop brim from filling holes

   By Allan Bennett, June 4
   • 3 replies
   • 302 views
   • 
   • Allan Bennett
   • June 5

4. Monosoupape dummy sort of....

   By Graff, April 28
   • 10 replies
   • 760 views
   • 
   • David Ovenden
   • May 1

5. Creality Ender 3 'Silent Board' queries

   By Allan Bennett, November 30, 2023
   • 23 replies
   • 1.8k views
   • 
   • Rashad Collie
   • April 26

6. 3D printers recommended 1 2

   By Zflyer, January 2, 2021
   • 27 replies
   • 1.9k views
   • 
   • EvilC57
   • April 7

7. 3D Printed Planeprint Jetwing - STRUCTURAL FAILURE WARNING

   By EvilC57, May 28, 2023
   • 24 replies
   • 1.7k views
   • 
   • bbuzz
   • March 26

8. 3D Print Whole Model - Caracara

   By Hoochykins, February 25
   • 22 replies
   • 1k views
   • 
   • Mike Chantler
   • March 21

9. Fusion 360 stopped working

   By Geoff Gardiner, March 14
   • 12 replies
   • 854 views
   • 
   • Geoff Gardiner
   • March 20

10. SD Card not seen by printer

    By Erfolg, December 8, 2023
    • 19 replies
    • 1.2k views
    • 
    • Erfolg
    • January 20

11. Surface finishing techniques

    By Ariel, December 20, 2023
    • 6 replies
    • 805 views
    • 
    • Ariel
    • January 8

12. Why is my printer printing bananas? 1 2

    By Allan Bennett, November 27, 2023
    • 26 replies
    • 1.3k views
    • 
    • PDB
    • December 9, 2023

13. Wheel Pants

    By Erfolg, November 22, 2023
    • 3 replies
    • 471 views
    • 
    • GrumpyGnome
    • November 22, 2023

14. In need of a wing bolt washer!!

    By Kevin Fairgrieve, November 12, 2023
    • 3 replies
    • 547 views
    • 
    • Kevin Fairgrieve
    • November 12, 2023

15. PrusaSlicer print settings question

    By Allan Bennett, September 6, 2023
    • 0 replies
    • 414 views
    • 
    • Allan Bennett
    • September 6, 2023

16. Filament not coming off reel easily

    By Allan Bennett, August 21, 2023
    • 14 replies
    • 661 views
    • 
    • Graham Bowers
    • August 23, 2023

17. A DH Venom tip tank

    By Simon Chaddock, August 4, 2023
    • 1 reply
    • 423 views
    • 
    • Simon Chaddock
    • August 14, 2023

18. How tough and durable are SLA printed parts - bellcrank for 3m glider

    By MikeQ, September 4, 2022
    • 20 replies
    • 1.6k views
    • 
    • John Minchell
    • July 21, 2023

19. Source of good quality lightweight PLA, please? 1 2

    By Allan Bennett, April 15, 2023
    • 25 replies
    • 2k views
    • 
    • EvilC57
    • June 28, 2023

20. CR Touch Ender 3 configuration info needed

    By Allan Bennett, January 11, 2023
    • 7 replies
    • 2k views
    • 
    • Paul Johnson 4
    • June 9, 2023

21. Ener 3 nozzle temperature issue

    By Allan Bennett, June 5, 2023
    • 6 replies
    • 598 views
    • 
    • Flying Squirrel
    • June 6, 2023

22. Resin tank versus diesel fuel

    By MikeQ, May 6, 2023
    • 17 replies
    • 1.1k views
    • 
    • J D 8 - Moderator
    • May 21, 2023

23. 3D Printed Wing Section for Glider

    By Daryn, April 17, 2023
    • 7 replies
    • 845 views
    • 
    • Andy Meade
    • May 2, 2023

24. A wing printed in LW-PLA

    By Simon Chaddock, March 7, 2023
    • 11 replies
    • 1.6k views
    • 
    • Simon Chaddock
    • April 11, 2023

25. Ender 3 feeder stalling

    By Allan Bennett, January 26, 2023
    • 20 replies
    • 1.3k views
    • 
    • Allan Bennett
    • January 28, 2023

26. Rhino 3D

    By david tilbury, January 14, 2023
    • 4 replies
    • 630 views
    • 
    • david tilbury
    • January 14, 2023