Stephen Jones

Forgive me what's MPM ? Maybe my D8 would not bind on the external module as it reports that the receiver is already in use.

Just tested external module and I am using D8 on the external for some models and D8 on the internal module. I have tried to bind a model that is on D8 internal to D8 on the external module and it will not bind. 🤔 Steve

I also have a multi module with Frsky protocol XJT not sure which version. Steve 🤔

I did try moving my Tx further away no use. So I guess it would be V2 / LBT but no info in that regards. My Radio FW is opentx-x9d+ V 2.2.3 don't really want to update it and lose connection to all my existing receivers.

Thanks, I have received my order from Slec very good service from them nicely packaged and very quick too. Only one problem and that was my fault 😩 Leading edge and triangle stock too small, should have ordered double the size than I did. 😩 So will have to put a fresh order in soon, not stopped the build for now as I already had Leading edges in stock top sheeting now on one of the wings. Steve.

Hi, I have bought two R6 mini E recivers from T9 but ca not bind them to my ACCST Taranis 9+ in D16 mode. So I am guessing it a V1 V2 issue, can I flash my Rx to Universal ACCST . ?> Do i need to update the firmware on the Rx https://www.frsky-rc.com/archer-plus-sr6-mini-sr6-mini-e/ Cheers for any help. Steve

And this is where I am at as I am waiting for some wood to arrive. Steve.

Once they have dried i un pin the wing from the board and fit the lower spars and once they have dried i turn the wing back over onto the building tabs and re pin the wing down and fit the webbing. And once all that has dried i can fit the leading Edge. And next is the false Trailing Edge. Steve.

I do not have a Lazar or CnC cutter but I do have a printer and a sharp knife 😉 So after cutting out all the Ribs i pin the to the building board over the top of my Wing Plan making sure all are positioned correctly and upright to the board I pushed my Pins through the ribs where the building tabs are to give better support and hold them straight. Now my spars can be fitted. At the same time i have slotted in my False leading and trailing edge. Steve.

And so i have started the build lets face it we can not do any flying here in the UK with all this bad weather we have been getting for the past few months. I have altered my Ribs, made them a bit thicker and lowered the building tabs. All my ribs fit onto one sheet 0f Balsa 4x36 and 2.5mm thick. These are semi-symmetrical and have wash out built in. Steve.

And So I have decided to do a little more styling and alter a few things along the way. So I am thinking of building two of them the first one will be called the G Guppy as it will be powered by a .25 IC engine. And the second one will be called the E Guppy as that one will be all Electric. But basically the same model with a few minor changes. I like the looks of this one even more. Steve.

Hello, Its been some time since I posted anything new of my own design so here I go again. Recently I flew one of my old models the Guppy. A 45 inch .15 IC powered sports model. Although the covering needed sticking down again and oil stains here and their I decided to fly it again at my new flying site and I really enjoyed flying again 😍 So I decided that this model deserves a revive. Steve,

I have managed to get some outdoor flying in. And I decided to fly an old Favorite of mine and get in so IC action in as I have not been doing so much IC as of late. So here is my Guppy. Only managed two flight due to my throttle servo dying on me. Good two flight though, need to get a new servo in there and get out with it again. Steve. (Happy Bunny) 😉

Here is one I built from a plan. Steve.