Alan Williams
Members-
Posts
95 -
Joined
-
Last visited
Never
Content Type
Profiles
Forums
Blogs
Gallery
Calendar
Downloads
Everything posted by Alan Williams
-
Thanks to Frank,I have read the instructions and got the info.Alan Williams
-
Hello all,I have just assembled a Max Thrust Yak54 EPO model.The kit was new but no handbook supplied.Can anyone tell me what the c of g should be.Thankyou.Alan Williams.
-
The 10cc was developed for the H9 Meridian.watch it on U Tube It flies the plane well.I have one and installed it in a ready 3,Just waiting for some weather to fly.Alan Williams
-
Please recommend me a covering material
Alan Williams replied to Ben B's topic in Building from Traditional Kits and Plans
Try easycote from Stan Yeos Phoenix models.lighter than profilm and applies easy.Alan Williams -
Thanks to Braddock.I have reset the carb as per instructions.now waiting for the weather to warm up.Alan Williams
-
Thanks for the reply.I will try that.Alan Williams
-
I have just noticed the heading doesent appear in the thread.The engine is a Thundertiger pro 61.Thanks.Alan Williams
-
No not the needle.This screw runs through the centre of the throttle lever.according to the belated reading of the hand book it is the air mixture screw
-
I have stupidly altered the air mixture screw whilst fitting the engine to a new air frame.I thought the screw removed the throttle lever!Can anyone tell me how many turnes out from fully closed.Thanks.Alan Williams
-
Hello All,I have broken the plastic wing retainer/fastener on my multiplex magister.It has given many years of service but has now bit the dust.I have searched all the main suppliers websites but cannot find a supplier.Has anyone bought one somewhere?If so could you advise.Thankyou.Alan Williams.PS.I live in Cumbria
-
The sister glider to the EP in the jp range is the JP SEAGULL.I have had this glider for about five years and it is a floater.my longest flight time on one climb is 45 mins.I only brought it in to land because my neck was aching.Alan Williams
-
Try Nitrotech MX2.
-
Gyro in a standard aeroplane
Alan Williams replied to Alan Williams's topic in All Things Model Flying
Thanks for all the input.I really have enjoyed the argument for and against.The author of the article damaged the aircraft.Nobody else has mentioned this.Alan Williams -
Gyro in a standard aeroplane
Alan Williams replied to Alan Williams's topic in All Things Model Flying
Thanks for the info.I will look at that -
In this months BMFA news there is an article on fitting gyros to a standard aeroplane.I find this of interest.Has anyone done it?If so can you report on whether it has any complications.Dear ED an article in the mag.would be interesting.Alan Williams
-
I put a hole in the fus.near to the component.Then I saw the end off a plastic spoon and glue it in place as an air scoop.Glue one facing the tail as an exit.It blends in and does not look out of place.Alan Williams
-
Next step after Diamond 2500?
Alan Williams replied to ricky's topic in Gliders and Gliding - General Discussion
Try the dynaflight Bird of Time.I electrfied mine,Stays up forever.The problem is trying to get it down.Alan Williams -
The wing tips on the windrider fox are too flimsy.I made a good landing after the first slope flight but found a broken wing tip when I picked it up.Alan Williams
-
Thanks Bert.I hope to do this job today.Alan Williams
-
Thankyou,I have replace this motor in the plane,Multiplex Magister.I am a Magpie and I hate throwing useful things away.I will take your advice.Alan Williams
-
Hello all I have a 700 watt brushless motor which has given a few years service.I have recently discovered some loose magnets in the casing.I am seeking advice on the best glue to use to make a repair.Has anyone done this?Thanks.Alan Williams
-
I am sure all these settings are on the dreamflight site along with some good video.Alan Williams