Andy Horsman Posted August 7, 2019 Share Posted August 7, 2019 More views Quote Link to comment Share on other sites More sharing options...
Stephen Jones Posted August 8, 2019 Author Share Posted August 8, 2019 Hi Andy, Looks interesting how does the foam feel compared to the Lidl. or Hobbyking type models. And how much Steve. Quote Link to comment Share on other sites More sharing options...
Andy Horsman Posted August 8, 2019 Share Posted August 8, 2019 It's quite a close cell foam and very smooth. I would say it's a bit smoother and finer than the Lidl. I think I paid around £16 each (I bought 2) but that was last year Quote Link to comment Share on other sites More sharing options...
Guy Hamilton-Fletcher Posted September 15, 2019 Share Posted September 15, 2019 Hi, sorry to bring this thread back from the dead but I have a couple of questions I have tried to straighten the wing with weights held flat for a few days and found that the wings just pops back to roughly the original polyhedral angle. Did you overbend it to remove the bend or use the spar to keep it flat? would the creases in the bottom surface not come out over time? Unfortunately I damaged the wing using a steam iron to try and straighten it as the the foam is less heat resistant than the stuff they use for the lidl model. I should have tried on a scrap piece first. I will be getting a replacement bolt glider for a second attempt. I have thought about cutting a slice from the topside and inserting a foam piece and gluing flat before putting a spar in, but that does seem less than ideal. Does anyone know what foam its made from as it doesn't seem to like standard CA unlike the lidl glider I have. I do have uhu por so will use that instead. Thanks Guy Quote Link to comment Share on other sites More sharing options...
Neil MacKinnon 1 Posted September 16, 2019 Share Posted September 16, 2019 Weights on the wings didn't work for me either. I gently and carefully over bent the wings, just take your time and you can feel the foam give and I didn't end up with any creases. I then used the carbon spars to keep the wings dead flat. You need foam safe CA for most of these models, I use it in combination with UHU Por and also epoxy depending on the application. Quote Link to comment Share on other sites More sharing options...
David Tayler Posted September 16, 2019 Share Posted September 16, 2019 I straightened the wings of my Lidle glider that I converted into a twin motor plane by cutting part way through them then filling the v with PU adhesive( Gorilla glue type of thing). Held it all down flat ,clamped to a board while the glue dried and it has worked a treat. I suggest some masking tape under the glue line to make sure it does not get stuck to the board! David Quote Link to comment Share on other sites More sharing options...
Stephen Jones Posted September 16, 2019 Author Share Posted September 16, 2019 Posted by Guy Hamilton-Fletcher on 15/09/2019 22:58:47: Hi, sorry to bring this thread back from the dead but I have a couple of questions I have tried to straighten the wing with weights held flat for a few days and found that the wings just pops back to roughly the original polyhedral angle. Did you overbend it to remove the bend or use the spar to keep it flat? would the creases in the bottom surface not come out over time? Unfortunately I damaged the wing using a steam iron to try and straighten it as the the foam is less heat resistant than the stuff they use for the lidl model. I should have tried on a scrap piece first. I will be getting a replacement bolt glider for a second attempt. I have thought about cutting a slice from the topside and inserting a foam piece and gluing flat before putting a spar in, but that does seem less than ideal. Does anyone know what foam its made from as it doesn't seem to like standard CA unlike the lidl glider I have. I do have uhu por so will use that instead. Thanks Guy Hi, Hardly bringing this thread back from the dead, Only 40 days since the last post. Anyway to answer your question my building room is the loft so possible the hot weather helped here. And i did rely on the spar holding the wing in place and it worked perfectly no creases on the bottom of the wing and still holds true to this day. I have bought two more and a cheep Chinese copy from eBay to compare the difference . This time i want to make a more aerobatic model and have a powered version. Steve. Quote Link to comment Share on other sites More sharing options...
Guy Hamilton-Fletcher Posted September 16, 2019 Share Posted September 16, 2019 Thanks for the advice guys. I will carefully overbend the wing as suggested before fitting the spar. Quote Link to comment Share on other sites More sharing options...
Guy Hamilton-Fletcher Posted February 26, 2020 Share Posted February 26, 2020 If I could ask what control throws did you guys use for the elevator. I have built it as an all moving tail plane similar to Steve Jones's model. Also what position did you end up using for the Center of Gravity ? I forgot to record the original position before getting halfway through the conversion. will post some pics when done Guy Quote Link to comment Share on other sites More sharing options...
Stephen Jones Posted February 26, 2020 Author Share Posted February 26, 2020 Posted by Guy Hamilton-Fletcher on 26/02/2020 20:45:03: If I could ask what control throws did you guys use for the elevator. I have built it as an all moving tail plane similar to Steve Jones's model. Also what position did you end up using for the Center of Gravity ? I forgot to record the original position before getting halfway through the conversion. will post some pics when done Guy Hi, This video gives you all the information you need for the powered version i did. But i you do not want to pause the video to read the info the Tailplane movement is 20 mm each way i also have 35% Expo to tame it down in the middle. Cog 35mm from the Leading Edge. 10 degrees down thrust. Hope this helps Steve. Edited By Stephen Jones on 26/02/2020 22:46:33 Quote Link to comment Share on other sites More sharing options...
Guy Hamilton-Fletcher Posted February 29, 2020 Share Posted February 29, 2020 Thanks Steve, that's really helpful. Guy Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.