Neil Grayson 1 Posted June 1, 2020 Share Posted June 1, 2020 I have an Eflite apprentice which I have been learning to fly with. Marvellous plane for a beginner but I now have a strange problem with it which I can't seem to resolve. I use the supplied DXe Transmitter. The elevator goes up and down correctly when first switched on but as soon as I put the throttle up to 50 percent the elevator refuses to move down and only moves up about 2mm. Switching off the receiver power puts everything back to normal until the throttle is again put up to 50 percent. I have tried plugging the rudder servo into the elevator socket on the receiver and the same things happens. I have tried a different transmitter and the same problem is there. I do suspect it is the ESC, any idea how this can be reset? Has anyone got any idea what is happening and where the fault lies as this problem is driving me mad especially as lockdown has just been lifted up here in Scotland and I can't fly my plane? Quote Link to comment Share on other sites More sharing options...
Dwain Dibley. Posted June 1, 2020 Share Posted June 1, 2020 The manual says that in beginners mode the pitch and roll surfaces are restricted. Make sure you are not in this mode by mistake. I'm guessing there should be a switch on the TX to switch modes. D.D. Quote Link to comment Share on other sites More sharing options...
Jason-I Posted June 1, 2020 Share Posted June 1, 2020 Try reversing the panic button - Sounds like you are stuck in panic mode. Note that the receiver is programmed to add a small amount of up elevator as throttle increases beyond 50%, which is why you are seeing the up elevator movement as you advance the throttle. Edited By Jason-I on 01/06/2020 22:53:35 Quote Link to comment Share on other sites More sharing options...
Neil Grayson 1 Posted June 1, 2020 Author Share Posted June 1, 2020 Hi Dwain. Thanks for your advice but no even in beginners mode you should be able to apply some down elevator. It is the same in beginners, intermediate or expert mode. Quote Link to comment Share on other sites More sharing options...
Neil Grayson 1 Posted June 1, 2020 Author Share Posted June 1, 2020 Hi Jason. Thanks for your advice. The issue did start when I was reversing controls for my other plane. Will give it a try and get back to you with the result. Very impressed with the swift replies with my issue. Quote Link to comment Share on other sites More sharing options...
Jason-I Posted June 1, 2020 Share Posted June 1, 2020 As a test, you can try pressing and holding the panic button whilst wiggling the elevator. If the elevator moves normally with panic button depressed, then the panic channel is indeed reversed. Quote Link to comment Share on other sites More sharing options...
OZ e flyer Posted June 2, 2020 Share Posted June 2, 2020 Probably not the ESC. Sounds like the problem may be with the receiver or tx program and as Jason says, possibly a reversed panic switch. I assume all the other control surfaces work ok? I don’t have the manual for my apprentice at hand but I’m pretty sure there is a way outlined in the manual to do a reset. ive been flying my apprentice for a few years now and I still enjoy flying it. Almost always on expert mode now. But it performs really well and I get great flight times out of it. It has been banged up and rebuilt or repaired a bunch of times now but it’s a tough little plane. hope you enjoy yours as much as I enjoy mine. Quote Link to comment Share on other sites More sharing options...
Neil Grayson 1 Posted June 2, 2020 Author Share Posted June 2, 2020 Hi Jason. Yes that has worked. 2 flights today and working fine. Presumably the Panic button channel should be reversed and I have put it to normal when I have been switching between my 2 planes. Many thanks for your help and to everybody else who responded so quickly. I will certainly use this forum in future and hopefully I can help someone with their problems. My Apprentice is a great plane. I have built a balsa tail for mine as I found the original was very flimsy and easily damaged not to mention expensive at £23 a go. I went through 3 sets! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.