MikeQ

Lol, yeah, if thats how you see it Don. Treat it like a pub quizz question. More fun that way. Anyway, lets hope its a good season for flying 😀 cheers mike

Anyone spot the link between Ukraine, Serco, farmers being disinherited, and many other things besides?

Any particular brand or model. Not all £1 a hair brushes will be created equal 😀

Some useful info on Stunthanger using Zinc Sterate as a filler. Looks way lighter than talc. https://stunthanger.com/smf/paint-and-finishing/zinc-stearate I’ll check out the boat supplies for micro ballons. cheers mike

Hi Don you need to get out more . Microballoons at £10 per 250ml from LMS … i’d say thats pretty expensive. where did you get 1.5 litre tubs from? So you haven’t used Zinc Sterate then? Cheers mike

Hi anyone used Zinc Sterate in dope as a home brew balsa filler? i’ve used talc (heavy) and microballons (expensive). Cheers mike

Hi for those that do tissue and dooe 😀. What dooe brushs or mops do you use to apply dope or banana oil? i use a 3/4” flat brush but can take a while to do a decent sized model. Any brands recommended based on experience. cheers mike

Will check them out thanks. Thanks for the recommendations.

Hi is it me or have RC bits and bobs prices gone through the roof, if they are available. Ive run short out of some long held stock and thought I’d buy some new for upcoming project. Anyone have suitable alternatives to Robart 3mm hinge pins or Dubro 3mm (4-40) ball links? cheers mike ps Ive seen the 3mm hinge pins sold in bulk packs ‘loose’. Anyone successfully assembled and ‘pinned’ them. Can’t be too hard but happy to see what anyone has done 😀

Hello John thanks for the compliment. I wish i could progress faster but i have my finger in too many modelling poes and a shorter attention span as I get older 😆 I’m like John Shuttleworth with ‘10 margarines on the go’. cheers mike

Hello Minicraft good as new. It was an RS 550 motor on examination. Closest I could get at reasonable price was this one … https://www.amazon.co.uk/dp/B07GYQT8SD?ref=ppx_yo2ov_dt_b_fed_asin_title Drops right in. Windings must be different to original as its about twice as fast and seems to want to take off at top speed 🤣 Anyway, sounds and runs super smooth now, at low to medium speed 😃

Hi on a related topic. Z bends in say 2mm … i’ve always struggled to produce anything neat. Like today. Commercial versus my attempt bottom. Are Z bend pliers really any good? This kind of thing https://www.rcworld.co.uk/acatalog/Z-Bend-Pliers-5537318.html

Hello I’ve had my Minicraft MB450 bench sander for 30yrs but the motor is on its last legs. https://www.worthpoint.com/worthopedia/minicraft-mb450-mb-450-bench-sander-267694901 Needs a flick to get it going. Could be the commutator/brushes. Makes a screeching noise despite blowing it out quitr often with compressed air. Anyone had similar issues and does anyone know of a drop in motor replacement? Must say, its been absolutely fantastic value over the years. Mike

Hello Nigel i’ll have a look. cheers mike

Hi Richard I was probably being a bit lazy and hoping someone would come back with a specific section or two that I can just select in DevWing and away we go. Its not a big deal as like you say, just about any half decent semi symmetrical section will be good to go. Just being lazy and its always worth throwing a question out there 😀 cheers mike

Hi any opinions on best all round section to use for a WW2 fighter type model, low wing. Will be electric powered. P51, FW190, Tempest, you get the idea. Ideally not a thick chunky ClarkY. cheers mike

Hi the 400 micron I used isn’t floppy. Rigid enough for what I wanted on the Canberra. 1mm would seem more sensible on something like the Loaded Dice mentioned. If its Park Flyers I would say 400 or less will be ok. One thing I found was that depending how hot you get the sheet and how well distributed the heat is across the sheet, you can go too thin in the middle when sucked onto the plug. Best get hot across the whole sheet. Probably why using an oven I was much more successful than a heat gun. Also, make sure you lift the plug off the bed with scrap balsa or something. cheers

Hi Nice job. I made one a couple of years ago. Half way down the thread theres a link to some decent material i’v used for canopies a few times now. Better than pop bottles 😀 One thing I discovered that helped improve suction was to fill 90% of the box with foam. Reduces the volume. I think i have about 10-15mm air space under the holes so to speak.

Hello both worked a treat. I had a couple of options incorrect re paper size and printer/plotter. Thanks for the help. 😀 mike

Hi Nigel that would be really useful thanks. I’ll give it another go again. cheers mike

Hi still not working for me. must be being really dense 🤣 mike

Hi Nigel will give it a go. cheers mike

Hi I must be being thick. I can’t figure out how to print a plan 1:1 scale, across multiple sheets of A4, in AutoCAD. I’ll sellotape together to use. This is just to a regular laser jet printer as opposed to a plotter. Anyone managed to do this? Cheers Mike

Cockpit instruments mostly finished too.

Hello edging further forward a little bit. Been practicing painting pilots. Happy with this fella so far. Need a bit of glaze medium on visor and some decor on helmet and a bit of panel wash to finish off. This is just a test run. I’ll actually go for the colour scheme of the little orange chap. Better contrast in dark cockpits. Vallejo Youtube tutorials particularly useful.