Ingrid Lunau 1 Posted February 25, 2023 Share Posted February 25, 2023 Hello, Dont know if anyone can help on this matter. I have purchased an E-Flite 90mm DF Viper. I have bound the model to my DX9 in safe mode. However, I am unable to allocate a switcgh to this channel. These are the settings on my TX under Channel Assignments. 6 AUX1: Flap 7 AUX2: Aux 2 8 AUX3: Aux 3 9 AUX4: Aux4 Next: Channel Input config 6 AUX1: N/A 7 AUX2: E 8 AUX3: RKnob 9 AUX: B Channel 9 is the one that I have selected for the SAFE switch. Any helpwould be gratefully recieved. Robert Quote Link to comment Share on other sites More sharing options...
Frank Skilbeck Posted February 25, 2023 Share Posted February 25, 2023 Have you gone through the procedure to teach the Rx the safe switch channel as shown on page 9 of the instructions Quote Link to comment Share on other sites More sharing options...
steve too Posted February 25, 2023 Share Posted February 25, 2023 There is a downloadable setup for for this model. Click on manuals & support on this page https://www.horizonhobby.com/product/viper-90mm-edf-jet-bnf-basic-with-as3x-and-safe-select/EFL17750.html# and then follow the links until you get to the eflight viper 90mm on Google Drive. Quote Link to comment Share on other sites More sharing options...
Ingrid Lunau 1 Posted February 26, 2023 Author Share Posted February 26, 2023 13 hours ago, Frank Skilbeck said: Have you gone through the procedure to teach the Rx the safe switch channel as shown on page 9 of the instructions Many times ! Quote Link to comment Share on other sites More sharing options...
Ingrid Lunau 1 Posted February 26, 2023 Author Share Posted February 26, 2023 10 hours ago, steve too said: There is a downloadable setup for for this model. Click on manuals & support on this page https://www.horizonhobby.com/product/viper-90mm-edf-jet-bnf-basic-with-as3x-and-safe-select/EFL17750.html# and then follow the links until you get to the eflight viper 90mm on Google Drive. SHALL GIVE IT go. Thank you. Quote Link to comment Share on other sites More sharing options...
Frank Skilbeck Posted February 26, 2023 Share Posted February 26, 2023 Check on your servo monitor screen that the chosen switch is active on that channel. Quote Link to comment Share on other sites More sharing options...
steve too Posted February 26, 2023 Share Posted February 26, 2023 6 hours ago, Ingrid Lunau 1 said: SHALL GIVE IT go. It's not very sophisticated, but it gives you a starting point. Quote Link to comment Share on other sites More sharing options...
Ingrid Lunau 1 Posted February 26, 2023 Author Share Posted February 26, 2023 20 hours ago, Frank Skilbeck said: Have you gone through the procedure to teach the Rx the safe switch channel as shown on page 9 of the instructions Many times Quote Link to comment Share on other sites More sharing options...
Robert Putley 1 Posted February 26, 2023 Share Posted February 26, 2023 I have set up the 3 position switch B. Now I have another problem!! At position 2, we are on AS3X. Position 1 & 0, nothing , no Safe, no AS3X! The Viper is programmed for Safe as it cycles twice after plugging in the battery. So, what next?! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.