Stephen Grigg Posted November 1, 2009 Share Posted November 1, 2009 I looked in the back of my Espace this morning and was horrified to see my tool box had run into the rear of my Renegade ans smashed the rudder clean off.Ive a space walker in my bedroom and the fin has been broken.My models seem to suffer more damage on the ground than in the air.Do you suffer similarly? Quote Link to comment Share on other sites More sharing options...
Andy Harris Posted November 1, 2009 Share Posted November 1, 2009 Yep! As soon as the number of models exceeds 2, the probability of 'transport' rash increases exponentially. Miserable weather today, time to put some balm on the hangar rash. Andy Quote Link to comment Share on other sites More sharing options...
Bob Cotsford Posted November 1, 2009 Share Posted November 1, 2009 i took to putting my flightbox in the front passenger footwell in an attempt at avoiding car-rash, but now the models slide into each other instead of the box.The worst case of hangar rash was when I caught one of the cats sharpening her claws on a wing Quote Link to comment Share on other sites More sharing options...
Former Member Posted November 1, 2009 Share Posted November 1, 2009 [This posting has been removed] Quote Link to comment Share on other sites More sharing options...
Phil Claridge Posted November 1, 2009 Share Posted November 1, 2009 i put my flight box on the floor between the front and back seats along with any 12v batteries and my tin lipo box i lay my folding chair down and rest my planes on that with the wheels locking into the arms and legs of the chair, but i still manage to clout elevators and rudders getting them in and out Quote Link to comment Share on other sites More sharing options...
Stephen Grigg Posted November 1, 2009 Author Share Posted November 1, 2009 Good advice Eric,my problem OIve discovered is the rails for the removed seats allow the box to slide at high speed even enhen driving slowly.Im normally packed to the gunnells so nothing can move Quote Link to comment Share on other sites More sharing options...
Terry Whiting Posted November 2, 2009 Share Posted November 2, 2009 Last year I made a number of 'wing bags' which certainly helped in storage and during travelling . The mateial used was a roll of Wicks radiator insutating quilted aluminium faced plastic, (phew what a mouthfull) and clear re-enforced 50mm wide tape. Quote Link to comment Share on other sites More sharing options...
Stephen Grigg Posted November 2, 2009 Author Share Posted November 2, 2009 I ve cured my prop through the wing problem by having bungies at the roof handles and the wings are safely up there.As I drive along 1 often gives me a comforting pat on the head Quote Link to comment Share on other sites More sharing options...
Aero120 Posted November 2, 2009 Share Posted November 2, 2009 15mm Pipe lagging makes an excellent way of protecting wings and tail planes. Tear open the split and slide it on to the wings etc. Available from most Diy outlets and easy to fit and remove for transport. To cure the odd dent in balsa, inject the dented area with water with a syringe and needle. If you haven't access to these then make small slit in the covering with a scalpel and position the area so the surface is horizontal and place a bubble of water over it and then prod it to wet the wood beneath the covering and it will be sucked in and over the next hour or so inflate the damaged area. Just keep the outer surafece wet so it can be drawn inside. Quote Link to comment Share on other sites More sharing options...
Simon Roberts Posted November 2, 2009 Share Posted November 2, 2009 Ive just changed my car to a new Seat Leon thinking more room would be better! I put 2 models in over the weekend and im now having to do the same and repair the rudder on my Jumper 25 and a prop on my Ready Mk3. Quote Link to comment Share on other sites More sharing options...
batcho99 Posted November 2, 2009 Share Posted November 2, 2009 Bungee cords i've found work well. The worst models to transport are the ones with wheels fixed to the wings, like my geebee! Covering sharp pointy props with some pipe lagging helps too. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.