Adrian Smith 1 Posted October 26, 2016 Share Posted October 26, 2016 while I don't have problem tightening up a prop on an I/C engine, I can' t see how to do it successfully on an electric motor as the barrel of the motor turns as well. What am I to do as I am missing something? Quote Link to comment Share on other sites More sharing options...
Biggles' Elder Brother - Moderator Posted October 26, 2016 Share Posted October 26, 2016 Is the prop a little lose on the shaft Adrian? That might cause a prolem. TBH I usually find that if I do it it up finger tight (holding the shaft) then subsequently pinching it up tight with a spanner whilst holdng on blade of the prop isn't a problem. BEB Quote Link to comment Share on other sites More sharing options...
Cliff 1959 Posted October 26, 2016 Share Posted October 26, 2016 I thought this was going to be a question on Doping tissue, now I'm showing my age lol. Quote Link to comment Share on other sites More sharing options...
Chris Bott - Moderator Posted October 26, 2016 Share Posted October 26, 2016 Adrian in this sort of situation I have sometimes got away with roughening the face of the motors prop driver and the rear of the prop to make just enough friction. In one case I ended up glueing a disk of sandpaper to the back of the prop. Quote Link to comment Share on other sites More sharing options...
Adrian Smith 1 Posted October 26, 2016 Author Share Posted October 26, 2016 Well the spinner, despite using a spanner to tighten the prop driver nut, still turns slightly. The idea of installing a disc of sand paper might just work. I have used a dab of threadlock on the prop nut but I am not convinced all will be well. I will give it a try. Quote Link to comment Share on other sites More sharing options...
Martin Harris - Moderator Posted October 26, 2016 Share Posted October 26, 2016 Is there sufficient thread to prevent the nut "bottoming"? Quote Link to comment Share on other sites More sharing options...
Adrian Smith 1 Posted October 26, 2016 Author Share Posted October 26, 2016 Yes Martin there is plenty of thread so I don't think that is the problem. Quote Link to comment Share on other sites More sharing options...
Dave Hopkin Posted October 26, 2016 Share Posted October 26, 2016 I am assuming the culprit is the compression adaptor and that the motor is buried inside a cowl? You can try holding the prop and applying a slight twisting pressure so the prop barrel grips the shaft giving enough purchase to tighten the nut sufficiently tight for the adaptor to grip the shaft Failing than a dowel can be used to jam/wedge the motor can while you tighten the prop nut Quote Link to comment Share on other sites More sharing options...
Mike Blandford Posted October 26, 2016 Share Posted October 26, 2016 I frequently use a hacksaw to cut a slot into the front of the threaded part of the prop adapter. This allows me to use a screwdriver in the slot to prevent the prop adapter rotating while I tighten the prop nut. Mike. Quote Link to comment Share on other sites More sharing options...
Adrian Smith 1 Posted October 26, 2016 Author Share Posted October 26, 2016 Yes you got it Dave. Motor tucked in the cowl as you say. I think I will keep in mind the dowl trick in case all else fails. Quote Link to comment Share on other sites More sharing options...
Dave Hopkin Posted October 26, 2016 Share Posted October 26, 2016 Mikes slot cutting method is also a good one that I have resorted to in the past, though I use the dremmel to cut the slot Quote Link to comment Share on other sites More sharing options...
Adrian Smith 1 Posted October 26, 2016 Author Share Posted October 26, 2016 Yes Mike's method is a good one. I have a Dremel too. Quote Link to comment Share on other sites More sharing options...
Allan Bennett Posted October 26, 2016 Share Posted October 26, 2016 I've resorted to gripping the protruding threaded end of the shaft in a pair of long-nose pliers in the past, just enough to get the nut tightened down enough that the collet grips the shaft. Then holding the prop while applying the final torque. But Mike's slot idea sounds even better, for my method sometimes slightly damages the threads on the shaft, resulting in similar problems when trying to get the nut off! Quote Link to comment Share on other sites More sharing options...
Denis Watkins Posted October 26, 2016 Share Posted October 26, 2016 You are certainly not dopey Adrian, a dope would not ask a good question for assistance Edited By Denis Watkins on 26/10/2016 21:45:22 Quote Link to comment Share on other sites More sharing options...
Adrian Smith 1 Posted October 26, 2016 Author Share Posted October 26, 2016 Thanks Denis. It is just that being used to hefty petrol aircraft safety is a major consideration. Even with a comparatively small electric I just thought I needed be sure I was doing right - out of control props is my big phobia. Quote Link to comment Share on other sites More sharing options...
Adrian Smith 1 Posted October 27, 2016 Author Share Posted October 27, 2016 Well I think I have solved it with out any sort of prop shaft modifications. I managed to get some pliers on the the prop driver scallops (shown above) through the cowl top to hold the shaft still to allow me to tighten the nut to my satisfaction. Seems to have done the trick. Thanks for all the advice gents. Edited By Adrian Smith 1 on 27/10/2016 11:53:20 Quote Link to comment Share on other sites More sharing options...
PatMc Posted October 27, 2016 Share Posted October 27, 2016 May not be applicable for Adrian but I file a couple of flats on the prop driver to take a spanner (Actualy as the driver is ali I use a sanding disc) as per attached photos. For a close fitting spinner I use a thin, cheap stamped metal spanner. Quote Link to comment Share on other sites More sharing options...
Shaunie Posted October 27, 2016 Share Posted October 27, 2016 Just a reminder that of course the prop driver needs to be properly tight before flight. I saw a twin go in on takeoff when it spat the adaptor off the motor shaft, a spin ensued before the pilot identified the problem. A couple of months ago I was doing touch and goes with my foam-e Wot4, I powered up and it spat the prop adaptor of the motor while it was on the ground and rolled to a stop. I'll often run the motor with no adaptor on it and touch the spindle with a bit of wet and dry to take the shine off. Shaunie. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.