Daren Cogdon Posted November 24, 2023 Share Posted November 24, 2023 I have a few sheets of polystyrene - the kind of thing that's used for packaging in things like fridges, for example (in fact, I think this was from a fridge!) It's pretty flimsy, but could it be used as a construction material? I would say it's about 10mm thick, at most. If suitably reinforced with, say, PVA and brown paper? Quote Link to comment Share on other sites More sharing options...
Nigel R Posted November 24, 2023 Share Posted November 24, 2023 White bead foam has been used for ages as a core material for wings and things. Packaging for white goods will probably be quite "heavy" foam though. Quote Link to comment Share on other sites More sharing options...
Martin Gay Posted November 24, 2023 Share Posted November 24, 2023 This own design A320 was built with the foam packaging from a shower screen! 5 Quote Link to comment Share on other sites More sharing options...
Daren Cogdon Posted November 24, 2023 Author Share Posted November 24, 2023 12 minutes ago, Martin Gay said: This own design A320 was built with the foam packaging from a shower screen! That's pretty awesome! Quote Link to comment Share on other sites More sharing options...
Daren Cogdon Posted November 24, 2023 Author Share Posted November 24, 2023 22 minutes ago, Nigel R said: White bead foam has been used for ages as a core material for wings and things. Packaging for white goods will probably be quite "heavy" foam though. Nah, this is pretty light. I have five sheets of it - three at 10mm and two about 12mm, and each sheet probably weighs about as much as the A3-sized foam-board sheets that I have lying around. Quote Link to comment Share on other sites More sharing options...
Graham Davies 3 Posted November 24, 2023 Share Posted November 24, 2023 Everything is possible. I have some 25mm sheets that protected my fridge when it was delivered. I laminated a few thicknesses and made cowls for several models from it! Quote Link to comment Share on other sites More sharing options...
SIMON CRAGG Posted November 24, 2023 Share Posted November 24, 2023 Yes is the answer!. We are modeller.......so anything is possible. I have done some experiments in the past, and it can make a good core, covered in brown paper and strengthened with a carbon rod. I would cut up a few small pieces and try out some different techniques. Worth a try at least!. 1 Quote Link to comment Share on other sites More sharing options...
Daren Cogdon Posted November 24, 2023 Author Share Posted November 24, 2023 I never thought about the carbon rod - definitely need to try that, too. Quote Link to comment Share on other sites More sharing options...
Ace Posted November 24, 2023 Share Posted November 24, 2023 A 1" wide strip of grass reinforced packing tape wrapped tip to tip top and bottom works very well in tension, light and easy to add. Quote Link to comment Share on other sites More sharing options...
kc Posted November 24, 2023 Share Posted November 24, 2023 What sort of "grass reinforced tape"? ordinary lawn grass? Anyway being serious - the foam used in foam wings was 1 pound per cubic foot stuff, so anything like that should be OK. Measure in inches - 1728 cu inches per cu foot of course. Quote Link to comment Share on other sites More sharing options...
Phil Curtis 1 Posted November 25, 2023 Share Posted November 25, 2023 Hornet photo below, made from B&Q insulation foam, strengthened leading edge with balsa and carbon spar in wing, flys superb. Plans from outer zone. 2 Quote Link to comment Share on other sites More sharing options...
Ace Posted November 25, 2023 Share Posted November 25, 2023 (edited) 17 hours ago, kc said: grass reinforced tape Dam auto complete and not checking 🥵 Edited November 25, 2023 by Ace Quote Link to comment Share on other sites More sharing options...
Simon Chaddock Posted November 25, 2023 Share Posted November 25, 2023 Daren As you can see from the replies polystyrene 'packing' foam has very little "structural" strength so it use is all about how it is reinforced. Obviously adding reinforcing to the surface of the foam is gives the best stiffness to weight ratio but it needs experience to use the right material(s) in the right way. Adding a high strength material like a carbon tube is relatively simple to do but provides no protection to the foam's soft outer surface. A combination of both of these techniques may provide the best solution. Using soft foam to build a plane, although it may be plentiful and free, is not quite as simple as it might appear. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.