Jump to content
Please be aware of scammers when using the Sale/Wanted forum areas

Alan Hilton

Members
 View Profile  See their activity

  • Posts

    318

  • Joined

  • Last visited

 Content Type 

Everything posted by Alan Hilton

  1. Alan Hilton
    Bill also makes turtle decks
  2. Alan Hilton
    The carb spray bar should ideally be level with the tank centre line but I have found that somewhere within the tank is ok .I had a DB 1/4 pup with a laser 200 v twin .The tank was way above the carb but the engine ran fine if I didn’t fly inverted
  3. Alan Hilton
    Same for me I won’t get started on mine till next autumn now
  4. Alan Hilton
    Carbon tet was used as dry cleaning fluid too .All chlorinated hydrocarbons are toxic
  5. Alan Hilton
    A mossy gets my vote
  6. Alan Hilton
    Have you tried setting the tx to pcm ?
  7. Alan Hilton
    Hi Richard I’m still up for one
  8. Alan Hilton
    Talk to George at 4 max he is clued up It’s also worth looking on. the recomended set up section on the same web page
  9. Alan Hilton
    JR tx charging sockets are negative centre post, which is the reverse of normal, connect a normal charger and its a problem .There is probably a fuse as mentioned before .Have a look in the battery compartment , if its not there take the back off
  10. Alan Hilton
    Poly c is water based polyurethane floor varnish, so its not fuel proof .I second Jon 2 pack is the way to go but use a chemical proof face mask .These are usually available from auto paint suppliers .
  11. Alan Hilton
    Very nice work looking good . Will we see the new one at Hastings later in the year?
  12. Alan Hilton
    I have found the ones from 4 max very good .
  13. Alan Hilton
    Bill Manley of Bill kits makes nice foam wings, saves ages when building aerobatic models and perform well.He needs tip and root sections and a plan view
  14. Alan Hilton
    The 30% Toni Clark Tiger I used to own flew just right on a Zenoah 38 turning a 22 x 6 prop
  15. Alan Hilton
    Take a sharp Stanley knife, put the tube on the bench ,then put the blade on the tube at 90 degrees to the tube ,then roll the tube back and forward using the knife to power the roll .It takes practice to keep the blade on the right place
  16. Alan Hilton
    My choice for a follow on is the acrowot .Its easy to fly and especially easy to land and will do aerobatics well
  17. Alan Hilton
    I sold Bert the tiger because my knackered back wouldn’t cope with big models any more .I flew it for years on a zenoah 38 and it was great .The prop was scale size (22 6 ) It flew scale like in most conditions .It was a bit tricky in a force 5 wind though .
  18. Alan Hilton
    You can use an old fridge compressor (backwards) for vac bagging as well .The Edward’s pump would be a bit powerful
  19. Alan Hilton
    Sounds like the esc is cream krackered try another one
  20. Alan Hilton
    What about a edf jet ?
  21. Alan Hilton
    Could be a George Formby impersonator rather than a fisherman
  22. Alan Hilton
    The original gangster 63 was great on an os 61 rf pumper its vertical performance was off the scale .If I did one today I would go for an os 91 surpass. I did modify the model to a tail dragger to accommodate the tuned pipe for the rf pumper
  23. Alan Hilton
    Watt even!!!
  24. Alan Hilton
    Wat was the question
  25. Alan Hilton
    Talk to or email 4max. George is good at this stuff .He needs to know weight span and ground clearance to be accurate
×
×
  • Create New...