Andy Stephenson Posted July 7, 2022 Share Posted July 7, 2022 PM replied. Quote Link to comment Share on other sites More sharing options...
Engine Doctor Posted July 8, 2022 Share Posted July 8, 2022 The FP engines were excellent if run correctly . Check for rock on the crank bearing bush. Enyas are IMO even better and bullet proof engines , however they are noisier than the FP . Enya bark. If there is rock on the crank bearing then engine will loose a little power and become thirsty spraying the extra fuel from behind the prop driver. This applies to all plain bearing engines although I've yet to see an Enya worn like this. Quote Link to comment Share on other sites More sharing options...
Andy J Posted July 10, 2022 Author Share Posted July 10, 2022 Well after all the recommendations for Enya managed to win the auction for an unran 25SS last night so it's just a matter of now finding a second one in similar condition. Quote Link to comment Share on other sites More sharing options...
Paul De Tourtoulon Posted July 10, 2022 Share Posted July 10, 2022 47 minutes ago, Andy Joyce said: Well after all the recommendations for Enya managed to win the auction for an unran 25SS last night so it's just a matter of now finding a second one in similar condition. No mean feat finding a second one, with any luck maybe one in the next couple of years ,,,😉 Quote Link to comment Share on other sites More sharing options...
jeff2wings Posted July 10, 2022 Share Posted July 10, 2022 Andy,I have two sc 25's with very low run time approx 1 hr, Quote Link to comment Share on other sites More sharing options...
Andy J Posted July 10, 2022 Author Share Posted July 10, 2022 Will keep that in mind Jeff. Spent £50 on three os 20's which will be too small for the GTC and a further £50 on the Enya so will wait to see if another Enya 25SS comes on the market in the next few weeks before I change engine type yet again. Quote Link to comment Share on other sites More sharing options...
Andy J Posted July 25, 2022 Author Share Posted July 25, 2022 Well have to say my Enya does run very well but strangely it starts better if flipped over clockwise. Quote Link to comment Share on other sites More sharing options...
Frank Skilbeck Posted July 25, 2022 Share Posted July 25, 2022 I have quite a few two strokes (and some four stokes) that hand start easier with a reverse flick. I've even seen an engine started this way by finger spinning the spinner clockwise. Quote Link to comment Share on other sites More sharing options...
Paul De Tourtoulon Posted July 25, 2022 Share Posted July 25, 2022 I always back flip my motors, they usually start but if they are really flooded al least you won't have to fumble around in the grass for your cone prop and nut whet it's all come unscrewed from the electric starter. 1 Quote Link to comment Share on other sites More sharing options...
Andy J Posted July 25, 2022 Author Share Posted July 25, 2022 Sure this could easily turn into a poll. So which way do others flick a prop to start an engine. Plus for the engine experts why should an engine start better when turned over in reverse. Quote Link to comment Share on other sites More sharing options...
RottenRow Posted July 25, 2022 Share Posted July 25, 2022 Backflicking isn’t turning the engine over in reverse, it’s tapping the prop. backwards against compression, when the engine fires it (hopefully) kicks and runs in the correct direction. One advantage is that you are never going to damage a flooded engine by forcing it over compression as can happen with careless use of an electric starter. The engine needs to be primed for it to backflick start, and you need to find the optimum amount to prime each of your engines (once the fuel has been drawn upto the carb). My flying friend always starts his engines by flicking back against compression, both two and four strokes. He has the knack. I don’t and it can take me several attempts, if it starts at all, so I normally start mine with a forward flick wearing a thick glove for smaller engines, and a starter for, say, 120 four strokes. Brian. Quote Link to comment Share on other sites More sharing options...
PatMc Posted July 25, 2022 Share Posted July 25, 2022 6 minutes ago, RottenRow said: Backflicking isn’t turning the engine over in reverse, it’s tapping the prop. backwards against compression, when the engine fires it (hopefully) kicks and runs in the correct direction. One advantage is that you are never going to damage a flooded engine by forcing it over compression as can happen with careless use of an electric starter. . But you can get a flooded engine to oscillate two or three times, firing & reversing direction each time as the piston nears TDC. A sure way to avoid a hydraulic lock is to install the engine inverted & turn it over once or twice by hand after priming & before connecting battery to plug. Quote Link to comment Share on other sites More sharing options...
Paul De Tourtoulon Posted July 26, 2022 Share Posted July 26, 2022 Flood engine, turn it over at least twice by hand to evacuate the excess fuel, hold prop, connect plug, a tiny bit of throttle, back flip. fly,,,,🥳 Quote Link to comment Share on other sites More sharing options...
PatMc Posted July 26, 2022 Share Posted July 26, 2022 4 hours ago, Paul De Tourtoulon said: Flood engine, turn it over at least twice by hand to evacuate the excess fuel, hold prop, connect plug, a tiny bit of throttle, back flip. fly,,,,🥳 Turning a flooded an upright mounted engine by hand does not always clear excess fuel accumulated in the bottom of the crankcase. When the engine fires the now more effective pump action can transfer the excess fuel to the top of the cylinder causing an hydraulic lock. Quote Link to comment Share on other sites More sharing options...
Paul De Tourtoulon Posted July 26, 2022 Share Posted July 26, 2022 2 hours ago, PatMc said: Turning a flooded an upright mounted engine by hand does not always clear excess fuel accumulated in the bottom of the crankcase. When the engine fires the now more effective pump action can transfer the excess fuel to the top of the cylinder causing an hydraulic lock. I haven't seen an engine mounted upright since a Cox 40 years ago. Quote Link to comment Share on other sites More sharing options...
Andy J Posted July 30, 2022 Author Share Posted July 30, 2022 Well thanks to Zflyer now have a second Enya 25, so I hope they are as good as some have declared. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.