Devcon1 Posted March 14, 2015 Share Posted March 14, 2015 Well trebor, if you look at picture 13 you are spot on.. I have a kettle. The sink would be a good idea but I had to draw a line, when the TV gets installed I could move in . The power point cost me £10.00 ish on the Bay. I do, however, have a fridge tucked under the worktop and I'm sure will spend the occasional night camping in the shed after a late building session so as not to disturb my good lady. A few more details on the build. The door, worktop, kitchen units/doors carpet, window carcass were sourced via a well known auction site. The Selotex/insulation where waste from a local building site. The guttering is recycled aluminium data trunking and the feather edge was recycled from the demolished shed. The half and half exterior was a compromise with my good lady, she said my "New England look" would dominate the garden . Regards John Quote Link to comment Share on other sites More sharing options...
trebor Posted March 15, 2015 Share Posted March 15, 2015 What you need is a z bed. As long as your other half brings the breakfast out in the morning. Quote Link to comment Share on other sites More sharing options...
Ausferret Posted May 1, 2016 Share Posted May 1, 2016 I am lucky enough to have a "hobby room" for the clean work which is airconditioned (gets hot here in Aus). The other is a workshop in the garage, not airconditioned unfortunately but OK for the messy work As per the original post neither has been "prepared" for the photos. Quote Link to comment Share on other sites More sharing options...
cymaz Posted May 1, 2016 Share Posted May 1, 2016 John, nice work! Great touches with the dart board and kettle....couldn't see any biscuits though Quote Link to comment Share on other sites More sharing options...
Devcon1 Posted March 10, 2018 Share Posted March 10, 2018 Edited By Biggles' Elder Brother - Moderator on 10/03/2018 10:46:15 Quote Link to comment Share on other sites More sharing options...
Devcon1 Posted March 10, 2018 Share Posted March 10, 2018 Edited By Biggles' Elder Brother - Moderator on 10/03/2018 10:47:03 Quote Link to comment Share on other sites More sharing options...
reg shaw Posted March 10, 2018 Share Posted March 10, 2018 Never noticed this topic, let alone its clone!! Here's a few pics of my den, wriggly tin, railway workshop style. Quote Link to comment Share on other sites More sharing options...
Roo Hawkins Posted March 10, 2018 Share Posted March 10, 2018 My glider workshop: Quote Link to comment Share on other sites More sharing options...
reg shaw Posted March 10, 2018 Share Posted March 10, 2018 Some great subjects in there Roo! Ian. Quote Link to comment Share on other sites More sharing options...
Roo Hawkins Posted March 10, 2018 Share Posted March 10, 2018 thanks reg or ian all my gliders are scratch built. the largest being a dg 800 at 6 meter span.. the one on the middle work bench is my new one and is a 1/3 scale fox putting the graphics on at the min .i have built 9 in the last 4 years. but I have to plan when I build because my work shop has no insulation in the roof .been looking at some of the great workshops on this thread. to plan how to do it. ROO Quote Link to comment Share on other sites More sharing options...
David Davis Posted March 11, 2018 Share Posted March 11, 2018 I have been rationalising the workshop/boiler room.. Although the restored Electric Junior 60 is the star of the show, you can see in this picture the steel shelves which I have assembled, bolted to the wall and to each other. I have another three shelves which I could use but some will have to be reserved for my P6 Rover spares. On the east wall near the boiler, a number of trainer and sports model fuselages are suspended. On the west wall, above the model's starboard wing, I've built a structure to hold the squadron's wings from 2x1 (50mmx25mm) timber and shelf brackets. I have some more models which I will need to find a space for. Quote Link to comment Share on other sites More sharing options...
Luther Oswalt Posted March 24, 2018 Share Posted March 24, 2018 Reg - You have a very nice shop. Great approach to the Construction Using Tin/Alum for the outside siding and roof! The wood interior is as nice as any one could want! Enjoy! Leo Quote Link to comment Share on other sites More sharing options...
GrahamWh Posted February 10, 2019 Share Posted February 10, 2019 Some marvelous examples in this thread guys. Mine is pretty small and simple. I was making a lot of mess around the house with bits of balsa etc. when building an Aerographics Sopwith Camel for RC some years ago, so my Mrs suggested I turn the spare room into a workshop - great! I started with a 2m x 1m ply table I built using parts from a bed frame then added one shelf, then another when space ran out, and now a sliding door cabinet on the back of the table for still more space. I still use the dining table sometimes though! . Quote Link to comment Share on other sites More sharing options...
Tony Bennett Posted February 10, 2019 Share Posted February 10, 2019 i have gone from this in the conservatory. via this to this. tghough i need to keep on top of the mess, or it will end up like the first picture again. Tony B Quote Link to comment Share on other sites More sharing options...
cymaz Posted February 10, 2019 Share Posted February 10, 2019 May I suggest anyone with a hard shiney floor put some old carpet down. It stops the nuts and screws escaping too far when you continually drop them.....well in my case anyway. And get several magnetic trays, they’re invaluable. Quote Link to comment Share on other sites More sharing options...
Pete Crosby Posted April 27, 2020 Share Posted April 27, 2020 Here is my small workshop/shed,. I keep models seperate in the house (no room in shed). Not as big as a lot of others but good things come from small spaces... I make, break mend and otherwise mess about in here ... 1 Quote Link to comment Share on other sites More sharing options...
Jon Laughton Posted April 27, 2020 Share Posted April 27, 2020 That's a great looking and well organised workshop Pete! Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted September 11, 2021 Share Posted September 11, 2021 Latest addition to my workshop is this bit of silliness. I had a spare noticeboard from my old home office/workroom which didn't have an obvious home and a tin of blackboard paint, so I came up with the notion of replicating one of those Squadron Readiness Boards that you see in the old war films. I set to with the Silhouette vinyl cutter and made a mock up for my warbirds. Just done for a bit of fun, but it does have some utility in keeping track of any minor or major fix-ups that need to be done. The name of the fictitious RAF station has been changed to protect the innocent. ? 2 Quote Link to comment Share on other sites More sharing options...
kevin b Posted September 11, 2021 Share Posted September 11, 2021 Not silly at all. In fact it's a good idea. Saves having to remember every model's state. In fact, I might just copy it ! Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted September 11, 2021 Share Posted September 11, 2021 (edited) I have all the detailed information on a spreadsheet - this is just for a bit of fantasy fun. The board is mounted on the wall at the mezzanine, which looks down on my model ready use racks - like this. ? Edited September 11, 2021 by leccyflyer added piccies Quote Link to comment Share on other sites More sharing options...
Upkeep Posted September 12, 2021 Share Posted September 12, 2021 ☝️ Fantastic !! Quote Link to comment Share on other sites More sharing options...
Upkeep Posted September 13, 2021 Share Posted September 13, 2021 Workshop 1 Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted September 13, 2021 Share Posted September 13, 2021 Wow! There's some impressive kit in there Upkeep and some brilliant storage ideas too. Love the tape storage idea.? Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted October 3, 2021 Share Posted October 3, 2021 (edited) Did a bit of reworking of my charging station today. I've changed over from exclusively charging at the field, to now doing some charging at home. I still do charge at the field, but I now prep for going flying by charging at least a few packs, since it's now a much longer trip to my old club site. For my local club site I can also just take enough packs for half-a-dozen flights and not bother with charging at the field at all. I initially set up with a pair of Bat Safes for charging and continued to use my Lipo Sacks for storage, along with a pair of Sentry Fire Safes for some of the less frequently used packs. I was never very happy with having the Lipo Sacks sat on the bench though and then saw these steel cabinets on FB marketplace, which would fit nicely under the bench. After a bit of a false start I finally managed to collect one yesterday and it's ideal for the job. Bottom shelf takes the Sentry Firesafe with the rarely used packs. Top shelf takes the Lipo Sacks, separated into charged and discharged packs. So it's just a matter of grabbing the Lipo Sacks when heading to the field. The cabinet is vented at the back. Turnigy Reaktor and Graupner Unimat 14 chargers are mounted on the lids of the Bat Safes, fed by a pair of 20amp power supplies, NiMh charging is taken care of by the Graupner Ultra Duo 30 plus in the middle, for peak detect fast charging and the multiport Robbe Lader for receiver packs in my gliders. 1s cells can be charged either with the little E-Flite chargers on the shelf, or via the multi-cell board with the Reaktor. My field chargers are then free to stay in the flight box, so the workshop chargers don't need to be disconnected to go flying. Edited October 3, 2021 by leccyflyer 1 Quote Link to comment Share on other sites More sharing options...
Steve Colman Posted October 3, 2021 Share Posted October 3, 2021 I have less space than that to do everything!? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.