Tosh McCaber Posted August 8, 2021 Share Posted August 8, 2021 I'm just about to buy some CA foam safe glue. After my fruitless request for info on Titan Wild Russian glue(- seems impossible on this side of Easteren Europe to source?! ), I see that there's one from BSI (Bob Smith Industries). However, before I buy, I wonder what go-to CA foam safe glues you all use? Any advice appreciated, thanks. Quote Link to comment Share on other sites More sharing options...
EarlyBird Posted August 8, 2021 Share Posted August 8, 2021 Multiplex Zacki2 has worked for me. Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted August 8, 2021 Share Posted August 8, 2021 Zap-O was always my favourite and performs very well. My one criticism is that once it is opened it does tend to go hard in the bottle in a few months, https://www.marionvillemodels.com/products/zap-odourless-foam-safe-ca-0-7-oz-20g?variant=21193700102¤cy=GBP&utm_medium=product_sync&utm_source=google&utm_content=sag_organic&utm_campaign=sag_organic&gclid=CjwKCAjwgb6IBhAREiwAgMYKRoNUP-98zaXQX6z_LxGGurA_3xqvWjJkhA9HBhdyLYlLfW2gglkASBoCLyIQAvD_BwE Deluxe Material Rocket Odourless also works well and seems to have a longer shelf life once opened. https://deluxematerials.co.uk/collections/cyanoacrylates/products/roket-odourless Quote Link to comment Share on other sites More sharing options...
Trevor Posted August 8, 2021 Share Posted August 8, 2021 The BSI one and the Deluxe Materials (Roket) one both work well. At the moment I’m using one branded ‘Logic’ which has a pin inside the cap which seems to help in keeping the nozzle clear. Quote Link to comment Share on other sites More sharing options...
Tosh McCaber Posted August 8, 2021 Author Share Posted August 8, 2021 Thanks so far for the replies! Trevor, how does Logic compare with the others? Presumably equally good? Leccy and all, regarding a piece of advice that I came across a long time ago, advised that storing CA glues in the freezer prolonged their life indefinitely. I just remembered that I have some that I stored 5 years ago(!), took it out, and it still is working perfectly! I think that this may work with opened bottles- may be worth trying, for the CAs that you don't use too often? Quote Link to comment Share on other sites More sharing options...
Trevor Posted August 8, 2021 Share Posted August 8, 2021 So far, I’m quite happy with the Logic foam safe CA. I haven’t done any systematic comparison though. I do keep unopened bottles in the fridge (not the freezer). Not sure I’d be allowed to put opened bottles in there! Quote Link to comment Share on other sites More sharing options...
Tosh McCaber Posted August 8, 2021 Author Share Posted August 8, 2021 I have them at the back of the bottom compartment, in a wee package, which the wife pretends she doesn't notice! (quite a large fridge freezer- posh!! That's why I bought it!) Quote Link to comment Share on other sites More sharing options...
Shaun Walsh Posted August 8, 2021 Share Posted August 8, 2021 (edited) I have used Element Essentials superglue on foam and it seems to work well, available from Element Games, about £4 for a 20g bottle. I suppose it will also depend on the type of foam too. Available in thick, medium and thin grades. Edited August 8, 2021 by Shaun Walsh Quote Link to comment Share on other sites More sharing options...
Geoff Copping Posted August 8, 2021 Share Posted August 8, 2021 I use Inwood Models own brand, I just built a Multiplex Heron with their thick foamsafe. It can be slow to go off but this can be useful when lining things up. Quote Link to comment Share on other sites More sharing options...
John Tee Posted August 8, 2021 Share Posted August 8, 2021 I've found that the kicker if you use it is what dissolves the foam. John Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted August 8, 2021 Share Posted August 8, 2021 2 hours ago, Tosh McCaber said: Thanks so far for the replies! Trevor, how does Logic compare with the others? Presumably equally good? Leccy and all, regarding a piece of advice that I came across a long time ago, advised that storing CA glues in the freezer prolonged their life indefinitely. I just remembered that I have some that I stored 5 years ago(!), took it out, and it still is working perfectly! I think that this may work with opened bottles- may be worth trying, for the CAs that you don't use too often? I'd heard that too and I store my CA in one of those little minifridges in the workshop. You just have to remember to take it out a while before you need to use it, or it becomes quite high viscosity. I use foam safe CA for most superglue jobs, since I can't really use ordinary CA too much as I get quite severe eyes, nose and chest reaction to them. Repairing my Seagull PC9 this weekend was only really possible with thin CA, as it was mostly piecing back shattered fragments, so it was a case of clamp the bits, hit it with the CA then leg it, leaving the workshop doors open and only going back 20 minutes later. Repairs are complete now, so it's fingers crossed. Quote Link to comment Share on other sites More sharing options...
John Lee Posted August 8, 2021 Share Posted August 8, 2021 3 hours ago, John Tee said: I've found that the kicker if you use it is what dissolves the foam. John Zap Foam Safe kicker works well with both foam safe & standard cynos. Quote Link to comment Share on other sites More sharing options...
Tosh McCaber Posted August 8, 2021 Author Share Posted August 8, 2021 2 hours ago, leccyflyer said: I'd heard that too and I store my CA in one of those little minifridges in the workshop. You just have to remember to take it out a while before you need to use it, or it becomes quite high viscosity. I use foam safe CA for most superglue jobs, since I can't really use ordinary CA too much as I get quite severe eyes, nose and chest reaction to them. Repairing my Seagull PC9 this weekend was only really possible with thin CA, as it was mostly piecing back shattered fragments, so it was a case of clamp the bits, hit it with the CA then leg it, leaving the workshop doors open and only going back 20 minutes later. Repairs are complete now, so it's fingers crossed. Glad things went well with the PC9 Leccy- see you (and it!) on the field! 1 Quote Link to comment Share on other sites More sharing options...
Murat Kece 1 Posted August 8, 2021 Share Posted August 8, 2021 Tosh I am using the deluxe materials ROKET odorless.. It take 15 to 30 secs to harden!! Quote Link to comment Share on other sites More sharing options...
Tosh McCaber Posted August 9, 2021 Author Share Posted August 9, 2021 Just by chance, I thought that I would try out my oft used Howdens/Screwfix MitreBond CA on a couple of scrap pieces of Depron (well- actually- the go-to B&Q substitute, their EPS substitute, which all our club members use- Depron being unavailable!) I couldn't believe it- the MitreBond worked perfectly, in seconds, with or without it's accellerator! Tryingn to pull the samples apart tore the EPS, rater than thejoint. I left the CA lying on the EPS for a few minutes to check for reaction- it actually set on the surface, with no degradation. Same thing with the accelerator. And, at £5.50 for 50g, it's a steal for any type of CA! Used by the Joinery Trade! 1 Quote Link to comment Share on other sites More sharing options...
Trevor Posted August 9, 2021 Share Posted August 9, 2021 Sounds like a good find! However, like leccyflyer, I exclusively use the foam safe formulations rather than the standard CA because I’m sensitised to the fumes. What’s Mitrebond like in that respect? Quote Link to comment Share on other sites More sharing options...
Tosh McCaber Posted August 9, 2021 Author Share Posted August 9, 2021 Probably about the same- rather less than some of the thinner ones though. I can remember way back that some of the (mainly) watery ones gave off visible fumes- like smoke! Fortunately, I guess that I'm one of the lucky ones not affected by any of the CA fumes! Quote Link to comment Share on other sites More sharing options...
Tosh McCaber Posted August 11, 2021 Author Share Posted August 11, 2021 An update. I have managed to get a chunk of regular expanded plystyrene, and gave it the CA test with the Mitrebond. Oops- the Mitrebond is not compatible with this regular (soft) stuff, used commonly for foam wing cores etc. However, I'm still very pleased that it works with my go to B&Q EPS substitute for Depron! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.