3D Printing

126 topics in this forum

1. Monosoupape dummy sort of....

   By Graff, 5 hours ago
   • 0 replies
   • 23 views
   • 
   • Graff
   • 5 hours ago
2. • 
   • 
   • 

3. Fusion 360 stopped working

   By Geoff Gardiner, March 14
   • 12 replies
   • 573 views
   • 
   • Geoff Gardiner
   • March 20

4. 3D Print Whole Model - Caracara

   By Hoochykins, February 25
   • 22 replies
   • 881 views
   • 
   • Mike Chantler
   • March 21

5. Surface finishing techniques

   By Ariel, December 20, 2023
   • 6 replies
   • 692 views
   • 
   • Ariel
   • January 8

6. SD Card not seen by printer

   By Erfolg, December 8, 2023
   • 19 replies
   • 1k views
   • 
   • Erfolg
   • January 20

7. Creality Ender 3 'Silent Board' queries

   By Allan Bennett, November 30, 2023
   • 23 replies
   • 1.3k views
   • 
   • Rashad Collie
   • Friday at 02:34

8. Why is my printer printing bananas? 1 2

   By Allan Bennett, November 27, 2023
   • 26 replies
   • 1.1k views
   • 
   • PDB
   • December 9, 2023

9. Wheel Pants

   By Erfolg, November 22, 2023
   • 3 replies
   • 395 views
   • 
   • GrumpyGnome
   • November 22, 2023

10. In need of a wing bolt washer!!

    By Kevin Fairgrieve, November 12, 2023
    • 3 replies
    • 409 views
    • 
    • Kevin Fairgrieve
    • November 12, 2023

11. PrusaSlicer print settings question

    By Allan Bennett, September 6, 2023
    • 0 replies
    • 364 views
    • 
    • Allan Bennett
    • September 6, 2023

12. Filament not coming off reel easily

    By Allan Bennett, August 21, 2023
    • 14 replies
    • 558 views
    • 
    • Graham Bowers
    • August 23, 2023

13. A DH Venom tip tank

    By Simon Chaddock, August 4, 2023
    • 1 reply
    • 380 views
    • 
    • Simon Chaddock
    • August 14, 2023

14. Ener 3 nozzle temperature issue

    By Allan Bennett, June 5, 2023
    • 6 replies
    • 517 views
    • 
    • Flying Squirrel
    • June 6, 2023

15. 3D Printed Planeprint Jetwing - STRUCTURAL FAILURE WARNING

    By EvilC57, May 28, 2023
    • 24 replies
    • 1.4k views
    • 
    • bbuzz
    • March 26

16. Resin tank versus diesel fuel

    By MikeQ, May 6, 2023
    • 17 replies
    • 969 views
    • 
    • J D 8
    • May 21, 2023

17. 3D Printed Wing Section for Glider

    By Daryn, April 17, 2023
    • 7 replies
    • 775 views
    • 
    • Andy Meade
    • May 2, 2023

18. Source of good quality lightweight PLA, please? 1 2

    By Allan Bennett, April 15, 2023
    • 25 replies
    • 1.7k views
    • 
    • EvilC57
    • June 28, 2023

19. A wing printed in LW-PLA

    By Simon Chaddock, March 7, 2023
    • 11 replies
    • 1.4k views
    • 
    • Simon Chaddock
    • April 11, 2023

20. Ender 3 feeder stalling

    By Allan Bennett, January 26, 2023
    • 20 replies
    • 1.1k views
    • 
    • Allan Bennett
    • January 28, 2023

21. Rhino 3D

    By david tilbury, January 14, 2023
    • 4 replies
    • 552 views
    • 
    • david tilbury
    • January 14, 2023

22. CR Touch Ender 3 configuration info needed

    By Allan Bennett, January 11, 2023
    • 7 replies
    • 1.7k views
    • 
    • Paul Johnson 4
    • June 9, 2023

23. Keeping filament dry

    By Allan Bennett, January 1, 2023
    • 12 replies
    • 890 views
    • 
    • GrumpyGnome
    • January 6, 2023

24. Fusion 360 basic advice needed please

    By Allan Bennett, December 18, 2022
    • 15 replies
    • 751 views
    • 
    • Allan Bennett
    • December 26, 2022

25. Beginner looking for advice.

    By Allan Bennett, December 7, 2022
    • 5 replies
    • 545 views
    • 
    • Allan Bennett
    • December 8, 2022

26. Ender 3 V2 Power Loss Recovery Surprise!

    By EvilC57, December 7, 2022
    • 1 reply
    • 2.3k views
    • 
    • Mark Parity
    • January 8, 2023