Chris Walby Posted December 23, 2020 Share Posted December 23, 2020 As the title suggests could forum members please post pictures/words on the various methods of attaching engine cowls (doesn't have to be just plastic/glass fibre). Hopefully this will be useful to future builder as reference options. Starting off with: long servo screw rubber backed washer - mixed results Captive nut, m3 screw and rubber backed washer - nice but a it tricky installing (any tip/tricks?) keyhole drop and lock with screw Anyone used Nylon screws? Mush be loads of other ways? Quote Link to comment Share on other sites More sharing options...
Frank Skilbeck Posted December 23, 2020 Share Posted December 23, 2020 Is this for IC or Electric? on electric I've used magnets with alignment pins on a couple of models, works very well. I can't claim any credit for this though as I first came across in on the Chris Williams designed ASK11 motor glider. Quote Link to comment Share on other sites More sharing options...
Ace Posted December 23, 2020 Share Posted December 23, 2020 3 or 4mm nylon cheesehead screws into tapped basewood blocks with the threads hardened with CA. Being nylon in wood doesn't vibrate loose (not on my IC 4*'s anyway) nor dose the nylon chew the cowl. You could dab the heads with humbrol for a colour match if required. Quote Link to comment Share on other sites More sharing options...
Trevor Posted December 23, 2020 Share Posted December 23, 2020 For a wooden cowl over an electric motor - cowl locates on cocktail sticks and secured by strips of matching covering. Or sometimes the motor can be mounted from the rear (access via the battery hatch) in which case there is no need for a detachable cowl at all. Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted December 23, 2020 Share Posted December 23, 2020 For plastic or fibreglass cowls, typically four or five small self tappers into the firewall, around the periphery. If the sides are balsa then I've sometimes inserted hard points from yellow Sullivan snake inners to screw those self tappers into. Metal cowls and larger heavier fibreglass items use larger self tappers into small blocks of hardwood engine bearer epoxied to the face of the firewall. As they are all electric I've not found the need for any vibration-resistant grommets. Quote Link to comment Share on other sites More sharing options...
Murat Kece 1 Posted December 23, 2020 Share Posted December 23, 2020 I use self-tapping screws tapped into firewall or wood/plastic inserts, sometimes in combination with magnets. Occasionally I use plastic washers/gaskets. Edited By Murat Kece 1 on 23/12/2020 09:14:15 Quote Link to comment Share on other sites More sharing options...
Peter Miller Posted December 23, 2020 Share Posted December 23, 2020 I use keyhole slots in the rear cowl former.These slide over screws in the firewall. Just slide the cowl up about 3/16" of an inch and it comes off.You need a latch at the bottom to stop it sliding up in flight although that is not too serious, it just looks untidy. Quote Link to comment Share on other sites More sharing options...
Eric Robson Posted December 23, 2020 Share Posted December 23, 2020 This is a tip from Richard Wills, I don't know about i.c but on electric a few dabs of silicane sealer will hold it firm without having to use screws. Quote Link to comment Share on other sites More sharing options...
Chris Walby Posted December 23, 2020 Author Share Posted December 23, 2020 Thanks guys, very helpful and keep he ideas coming, cheers Quote Link to comment Share on other sites More sharing options...
Brian Cooper Posted December 23, 2020 Share Posted December 23, 2020 Fit rubber grommets to the cowl and secure with self-tappers. Quote Link to comment Share on other sites More sharing options...
philip pember Posted December 23, 2020 Share Posted December 23, 2020 as Eric above said, silicon, mastic better or if wood on wood no more nails, if need to remove just slice down gap with scalpal. Quote Link to comment Share on other sites More sharing options...
Broken Prop Posted December 23, 2020 Share Posted December 23, 2020 For IC: Self tappers into hardwood,blocks on the firewall as others have stated. However I oversize the holes in the hardwood blocks and insert short lengths of fuel tubing into the holes, with a bit of CA. The screws bite into the tubing but retain some flexibilty against vibration. I also cut a small washer from fuel tubing and fit it under the head of the self tapper to improve the flexibility. Quote Link to comment Share on other sites More sharing options...
Martin McIntosh Posted December 23, 2020 Share Posted December 23, 2020 All too complex. For anything up to and including 50cc petrol I always use the grey plastic right angled brackets with two holes drilled on one side. These are fixed to the firewall with two No.2 self tappers, then after careful measurement one of these is added through from the outside for each. Drill the cowl 2mm and the bracket 1.6mm. By going into plastic they never vibrate out unlike screwing into ply. If one gets stripped due to over tightening it can always be replaced with the next size up. Just about to do a cowl fixing but could not get the correct ones so shall try an inferior variety. You can always make your own from some L shaped ABS. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.