Skippers Walker Posted May 6, 2023 Share Posted May 6, 2023 Which tool is best for reaming propellers please: Tapered or Stepped? I have to create a 3/8" (10mm approx) in a 15x8 nylon/plastic prop. Quote Link to comment Share on other sites More sharing options...
Nigel R Posted May 6, 2023 Share Posted May 6, 2023 I have a great planes reamer which was pricey but works really well. I think stepped is easier to keep properly aligned, although less versatile for obvious reasons. 1 Quote Link to comment Share on other sites More sharing options...
J D 8 Posted May 7, 2023 Share Posted May 7, 2023 Horrible things those tapered reamers as only a very small part of the hole is correct diameter. The leading edge of each section of a good stepped reamer is angled to ensure it align's in the prop hub. 1 Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted May 7, 2023 Share Posted May 7, 2023 I use 2 methods but use either drill bits or parallel (straight) reamers going up in size in stages. If I'm doing it by hand (smaller props) I hold the reamer in the vice and turn the prop over it by hand which tends to ensure that the prop is turning centrally around the reamer. The other method, for larger props, is to use the pillar drill, starting with a drill bit that exactly fits the existing prop hole and chucking that in the drill as this ensures that the prop is dead centre. Then, with the prop clamped in place I either use reamers or drill bits to enlarge the hole, the latest ones I did (wooden 20" and 21") needed taken out to 13mm and these were done in one pass with a very sharp drill bit. Reamers like these. 1 Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted May 7, 2023 Share Posted May 7, 2023 I prefer the stepped reamers, but find that they don't last very long before losing their edge, so I have three or four of them in my prop box. Have never really got on with the tapered reamer. With APC-E and similar props it's a boon having the insert in the back of the hub, which ensures a nice fit, though I always seem to end up using the insert with the smallest wall thickness. 1 Quote Link to comment Share on other sites More sharing options...
i12fly Posted May 7, 2023 Share Posted May 7, 2023 If drilling out a prop don't hold the prop by hand. I did but the drill 'grabbed' -like it does with plastic/nylon, the blade I was holding very firmly broke and the other one come round and cut my finger to the bone. Since then I fix the drill bit in the vice and 'wind' the prop on by hand. I increase the hole size by 0.2 or 0.3mm at a time. OK it takes a bit longer but every one is a good one, not oval or triangular hole as you can easily get. I have a set of sharp drills I keep specifically for prop drilling. 2 Quote Link to comment Share on other sites More sharing options...
Skippers Walker Posted May 8, 2023 Author Share Posted May 8, 2023 Thanks for all the comments, I've eventually ordered a stepped reamer, there appears to be quite a supply problem around the model shops?. Plenty of 'Great Planes' reamers in the US but the cost is transport costs are prohibitive! Cheers for now SW Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted May 8, 2023 Share Posted May 8, 2023 (edited) Loads on eBay from UK suppliers. £7.12 from Leeds Model Shop https://www.modelshopleeds.co.uk/catalog/advanced_search_result.php?keywords=reamer Edited May 8, 2023 by leccyflyer Added link Quote Link to comment Share on other sites More sharing options...
Christopher Wolfe Posted May 8, 2023 Share Posted May 8, 2023 On 07/05/2023 at 18:45, leccyflyer said: I prefer the stepped reamers, but find that they don't last very long before losing their edge, so I have three or four of them in my prop box. Have never really got on with the tapered reamer. With APC-E and similar props it's a boon having the insert in the back of the hub, which ensures a nice fit, though I always seem to end up using the insert with the smallest wall thickness. Stepped reamers with a pilot are a great option. To restore the edge I use one of these https://www.amazon.com.au/EZE-LAP-PAK4-Color-Coded-Diamond/dp/B000UVTDZC/ref=asc_df_B000UVTDZC/?tag=googleshopdsk-22&linkCode=df0&hvadid=407150668989&hvpos=&hvnetw=g&hvrand=17093705469081806272&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9072238&hvtargid=pla-596145147273&th=1 Only takes a few strokes as most commercial prop reamers are not made of tool steel. Definitely true the prop centre up with a pilot in a drill press or mill before cutting and check the prop balance after reaming. Which leads to - How many people actually balance their props? (Probably another thread) 😉 * Chris * 1 Quote Link to comment Share on other sites More sharing options...
Dickw Posted May 8, 2023 Share Posted May 8, 2023 4 minutes ago, Christopher Wolfe said: ............................................... Which leads to - How many people actually balance their props? (Probably another thread) 😉 I do, including folding props. Dick Quote Link to comment Share on other sites More sharing options...
GrumpyGnome Posted May 8, 2023 Share Posted May 8, 2023 I balance electric ones..... Quote Link to comment Share on other sites More sharing options...
Bruce Collinson Posted May 8, 2023 Share Posted May 8, 2023 Balance them all. There’s enough vibration going on without a simply fixed prop imbalance. + for Dubro balancer. BTC 1 Quote Link to comment Share on other sites More sharing options...
Martin Harris - Moderator Posted May 8, 2023 Share Posted May 8, 2023 100% 1 Quote Link to comment Share on other sites More sharing options...
Geoff S Posted May 8, 2023 Share Posted May 8, 2023 9 hours ago, Bruce Collinson said: Balance them all. There’s enough vibration going on without a simply fixed prop imbalance. + for Dubro balancer. BTC How do you balance them? Adding paint or sanding the wing tips? I sometimes do both. Quote Link to comment Share on other sites More sharing options...
Peter Jenkins Posted May 8, 2023 Share Posted May 8, 2023 (edited) 31 minutes ago, Geoff S said: How do you balance them? Adding paint or sanding the wing tips? I sometimes do both. I use Halfords spray clear quick drying varnish. Never by sanding. That's for both wood and composite props. The carbon props I use, Falcons, come balanced as they should for the price that's charged! Edited May 8, 2023 by Peter Jenkins 1 Quote Link to comment Share on other sites More sharing options...
Bruce Collinson Posted May 9, 2023 Share Posted May 9, 2023 I abrade the t.e. Of composites and do what Peter does with timber. For hub imbalance I add thick cyano on the light part of the hub. Plenty of destructions on the Web, if I recall the Dubro ones are sensible. Might try spraying composites. I only ever touch the tips if there is patent asymmetry or particular sharpness BTC Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.